TallyGenicom LGe06 Скачать руководство пользователя страница 45

Страница: 45 / 108

Chapter 3:

Printer Menus and the Control Panel

3–45

Print Selections Report

How to Print a Control Panel Selected Options Report

The organization of the multilevel menus is shown on the Control Panel Selected

Options Printout. All of the current selections are marked with an asterisk.

1. Toggle the Online key once or twice to clear the display and put the

printer Offline. Offline should be displayed and the green light should be

off.

2. Press the Menu key.
3. Use the Up or Down arrow keys until you see Help Menu on the display.
4. Press Enter.

Press the Enter key. The Form Length is set to 65, and an asterisk ap-

pears beside the number. Exit the menu mode by pressing the Clear key.

It's helpful to remember that at any time, you may leave a menu in one of two

ways.

•

Press the Clear key to leave Menu Mode and remain Offline.

•

Toggle the Online key to leave Menu Mode and return the printer to

Online.

The Control Panel Selected Options Report begins printing. When it's finished,

press the FF key, tear off the sheet and use it to become familiar with all of the

menu items.

Содержание LGe06













































































































Результаты поиска

Содержание LGe06

Отзывы:

Похожие инструкции для LGe06

Бренды по названию

Популярные бренды

TallyGenicom LGe06, Руководство оператора

Результаты поиска

Содержание LGe06

Отзывы:

Похожие инструкции для LGe06

Бренды по названию

Популярные бренды