Stryker InTouch FL27 series Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 252

Stryker InTouch FL27 series Скачать руководство пользователя страница 86

Return To Table of Contents

86

2141-209-002 REV H

www.stryker.com

Service Information

FOWLER ACTUATOR REMOVAL AND REPLACEMENT - (LITTER)

Tools Required:

•  Diagonal Pliers
•  Regular Screwdriver
•  Phillips Screwdriver #2
•  3/8” Combination Wrench

Procedure:

1.  Plug bed into wall outlet.
2.  Raise bed to the full up position.
3.  Raise the head end siderails to the full up position and set the brakes using one of the brake control locations or

by using the manual brake pedal.

4.  Working from the right side of the bed, step on the CPR pedal to lower the fowler all the way down.
5.  Raise the gatch to the full up position.
6.  Remove the three center base hoods (head, center, foot), then remove the right base hood.
7.  Using Needle-nose pliers, remove the two rue clips from the clevis pins holding the actuator.
8.  Using diagonal pliers, cut the zip ties securing the CPR cable to the actuator and the litter frame. Also cut the zip

ties securing the actuator cable to the wire harness.

9.  Unplug the actuator from the quick connect.
10.  Holding the actuator with one hand remove the clevis pins from the actuator and carefully lower the actuator down.
11.  Using a Phillips screwdriver and a 3/8” combination wrench, remove the CPR cable retaining screw from the right

CPR pedal.

12. Using a regular screwdriver, loosen the CPR cable retainer on the actuator just enough so it will move.
13. Slide the gray cable retainer lock towards the CPR cable retainer and unclip the CPR cable from the red actuator

release activator.

14.  Remove actuator.
15.  Reverse these steps to reinstall.
16.  When re-adjusting the cable retainer lock set,

set it to 1.00 +/- 0.06 as shown (right). When
the actuator is back in place, use needle-nose
pliers to reattach the spring to the center of
the clevis pin.

17. Test all bed functionality prior to putting bed

back into service.

1.00 ±0.06

«
...
84
85
86
87
88
...
»

Содержание InTouch FL27 series





























































































































































































































































Отзывы:

Нет отзывов