Stryker InTouch FL27 series Скачать руководство пользователя страница 59

Страница: 59 / 252

Return To Table of Contents

www.stryker.com

2141-209-002 REV H

Error Codes

Touch Screen Error Messages Name Definition

Cmd WO safe from room

Communication board has a network communication error (Check network
connections).

Cmd WO safe from room

Communication board has a network communication error (Check network
connections).

GPIO Failure Init

Initialization of the PCA9555 (GPIO expansion chip) failed (Replace control
board).

GPIO Failure Read

Reading from the PCA9555 (GPIO expansion chip) failed (Replace control
board).

GPIO Failure Write

Writing to the PCA9555 (GPIO expansion chip) failed (Replace control
board).

Limit switch head side rail right

Verify wiring to limit switch and replace limit switch.

Limit switch head side rail left

Verify wiring to limit switch and replace limit switch.

Limit switch foot side rail right

Verify wiring to limit switch and replace limit switch.

Limit switch foot side rail left

Verify wiring to limit switch and replace limit switch.

Foot Right Load cell over range

Foot Right load cell or cabling is damaged (Replace load cell).

Head Right cell over range

Head Right load cell or cabling is damaged (Replace load cell).

Foot Left Load cell over range

Foot Left load cell or cabling is damaged (Replace load cell).

Head Left Load cell over range

Head Left load cell or cabling is damaged (Replace load cell).

Motor Brake Overheat

Brake motor has ran too long (Leave motor stationary for 54 minutes).

Motor Brake Overload

Brake motor is drawing too many AMPS (remove restriction or replace
motor).

Motor Foot Overheat

Foot motor has ran too long (Leave motor stationary for 54 minutes).

Motor Foot Overload

Foot motor is drawing too many AMPS (remove restriction or replace motor).

Motor Gatch Overheat

Gatch motor has ran too long (Leave motor stationary for 54 minutes).

Motor Gatch Overload

Gatch motor is drawing too many AMPS (remove restriction or replace
motor).

Motor Head Overheat

Fowler motor has ran too long (Leave motor stationary for 54 minutes).

Motor Head Overload

Fowler motor is drawing too many AMPS (remove restriction or replace
motor).

Motor HL Foot Overheat

Foot lift motor has ran too long (Leave motor stationary for 54 minutes).

Motor HL Foot Overload

Foot lift motor is drawing too many AMPS (remove restriction or replace
motor).

Motor HL Head Overheat

Head lift motor has ran too long (Leave motor stationary for 54 minutes).

Motor HL Head Overload

Head lift motor is drawing too many AMPS (remove restriction or replace
motor).

Motor Zoom® Overheat

Zoom® motor has ran too long (Leave motor stationary for 54 minutes).

Motor Zoom® Overload

Zoom® motor is drawing too many AMPS (remove restriction or replace
motor).

No Error

Angle sensor failure or calibration issue.

One Motor Drive Short

Short on drive motor detected.

Safe WO Cmd from A1

Network A1 has a wiring issue (Check cabling).

Safe WO Cmd from A2

Network A2 has a wiring issue (Check cabling).

Safe WO Cmd from B1

Network B1 has a wiring issue (Check cabling).

Safe WO Cmd from B2

Network B2 has a wiring issue (Check cabling).

Scale ADC Error

Scale chip not calibrated. DC Control Board needs to be replaced.

Содержание InTouch FL27 series





























































































































































































































































Результаты поиска

Содержание InTouch FL27 series

Отзывы:

Stryker InTouch FL27 series, Руководство по обслуживанию, Страница: 59 / 252

Результаты поиска

Содержание InTouch FL27 series

Отзывы: