Stryker InTouch FL27 series Скачать руководство пользователя страница 84 | Manualshive

Страница: 84 / 252

Stryker InTouch FL27 series Скачать руководство пользователя страница 84

Return To Table of Contents

84

2141-209-002 REV H

www.stryker.com

Tools Required:

•  Needle-Nose Pliers
•  Diagonal Pliers
•  Jack (if needed)
•  2 x 4 (20” recommended)

Procedure:

1. Plug bed into wall outlet.
2. Raise the head end siderails to the full up position and set the brakes using one of the brake control locations or

by using the manual brake pedal.

3.  Remove head end base cover by pulling up and out.
4.  Remove center base cover by pulling up and out.
5.  Using diagonal pliers, cut the zip tie securing the actuator cable to the base frame.
6.  Using Needle-nose pliers, remove the rue clips from the clevis pins securing the actuator.

CAUTION

Do not remove the clevis pins.

7. If the bed will lower down, run it all the way down so the litter is supported by the base litter stop.
8. If the bed will not lower all the way down; using a jack and a 2 x 4, take tension off of the actuator

clevis pins by placing the jack and 2 x 4 between the bottom of the right side of the litter and the floor
and jack up just enough to take the litter weight off of the base frame (reference picture above).

CAUTION

Make sure that prior to jacking, the 2 x 4 is perpendicular to the floor.

9. Using the bed up/down controls, tap the up or down button to remove

tension on the clevis pins and remove clevis pins.

10.  Unplug the cable quick connect and remove the actuator.
11.  Reverse the steps to install the new actuator.
12.  Test all bed functionality prior to putting bed back in service.

Service Information

BED LIFT ACTUATOR (HEAD) REMOVAL AND REPLACEMENT - (BASE)

Step #8:

Locate Jack Stand between
floor and underside of Foot
Frame.

Floor

«
...
82
83
84
85
86
...
»

Содержание InTouch FL27 series





























































































































































































































































Отзывы:

Нет отзывов