Stober POSIDYN SDS 5000 Скачать руководство пользователя

Страница: 110 / 196

Integrated Bus

ID 442289.06

110

Operation manual POSIDYN® SDS 5000

KEEP

THINGS

MOVING

11.4.10 Deactivation of remote maintenance

NOTICE

Long timeout times on the teleserver!

Do not deactivate remote maintenance by turning the device off and on again because this will result in long

timeout times on the teleserver.



Use one of the following methods to deactivate remote maintenance.

Remote maintenance can be deactivated by the following events:

•

The machine technician switches off the signal (low level) specified in

A167

for all inverters on the IGB

network.

•

The service employee exits remote maintenance in POSITool by pressing the

button when an

Internet connection exists, or the

button for a LAN connection.

•

The Internet connection is interrupted (e.g., by a timeout ). Any specified session ID is always invalid. The

blue LED goes off. To establish a new connection, the procedure in chapter 11.4.8 Activation of remote

maintenance must be performed again.

Note the

A178

parameter when you deactivate remote maintenance. A number value is specified here as to

why the deactivation occurred and whether it was free of errors.

Also remember that after remote maintenance is concluded in POSITool, the signal specified in

A167

must

first be switched to low before remote maintenance can be activated again. Remote maintenance is then

activated again the next time a switch to high is made.

Information

Deactivate remote maintenance immediately after the job is finished. Do not let a request exist for

an unnecessarily long period of time.

Содержание POSIDYN SDS 5000





































































































































































































Результаты поиска

Содержание POSIDYN SDS 5000

Отзывы:

Похожие инструкции для POSIDYN SDS 5000

Бренды по названию

Популярные бренды

Stober POSIDYN SDS 5000, Руководство по эксплуатации

Результаты поиска

Содержание POSIDYN SDS 5000

Отзывы:

Похожие инструкции для POSIDYN SDS 5000

Бренды по названию

Популярные бренды