Stober POSIDYN SDS 5000 Скачать руководство пользователя

Страница: 180 / 196

Diagnosis

Operation

manual

POSIDYN®

SDS

5000

ID 44

22
8

WE KEEP THINGS MOVING

13.3.29 73:Ax2braketest

Triggering

Level

Response

Fault counter

For active brake management

in the SDS 5000, the time set in

B311

has elapsed without the

B300 Brake test

action with

active axis 2 having been

performed.

Cause 1 and 2: Fault, Cause 3:

Message

This fault only occurs with the enable switched off.

Z73

Cause

Description

Measure

Acknowledgement

1:B311Timeout

The time entered in

B311 Timeout for

brake test B300

has elapsed twice

without the

B300 Brake test

action with

active axis 2 having been performed.

Perform the

B300 brake test

action.

For the

Fault

level, the event can

be acknowledged for a duration

of 5 minutes to be able to

perform the

B300 brake test

action. If this time elapses

without the

B300 Brake test

with

active axis 2 being successfully

performed, the inverter changes

to the

Malfunction

state again. If

the

B300 brake test

action is

successfully performed, the

event is automatically

acknowledged.

2:Brake defective

When performing the brake test action

with active axis 2, the holding torque

entered in

B304

B305

could not be

applied or the encoder test run included

in the brake test was completed with

errors.

•

Perform the brake grinding function

and then the brake test.

•

Replace the motor.

3:Brake test required

Timeout for brake test has elapsed once

without the test brake action being

performed.

Perform the action

B300

test brake.

Содержание POSIDYN SDS 5000





































































































































































































Результаты поиска

Содержание POSIDYN SDS 5000

Отзывы:

Похожие инструкции для POSIDYN SDS 5000

Бренды по названию

Популярные бренды

Stober POSIDYN SDS 5000, Руководство по эксплуатации

Результаты поиска

Содержание POSIDYN SDS 5000

Отзывы:

Похожие инструкции для POSIDYN SDS 5000

Бренды по названию

Популярные бренды