Stober POSIDYN SDS 5000 Скачать руководство пользователя

Страница: 115 / 196

Integrated Bus

Operation manual POSIDYN® SDS 5000

ID 442289.06

KEEP

THINGS

MOVING

115

The

error category

stands for a group of errors:

The

Error value

specifies the error in an error category. The error values are specified for each error category

in the following.

In error category 00 hex, the error value is always 00

hex

The following errors can occur in error category 01

hex

The cause of these errors can be a faulty TCP/IP connection. Check the connection and the network settings.

The TCP/IP connection may also be blocked by a firewall. Check (e.g., with POSITool) whether the Teleserver

can be reached.

The following errors can occur in error category 02

hex

Error category

Description

hex

No remote maintenance is active or no error occurred.

hex

A socket error was determined (problems with the use of the TCP/IP connection).

hex

A firmware error was determined (internal firmware error).

hex

An HTTP error was determined (problems at the HTTP communication level).

hex

A TCP/IP error was determined (problems at the TCP/IP communication level).

hex

An error of the Teleserver Client application was determined.

hex

A DNS error was determined (problems with the DNS resolver).

hex

A proxy error was determined (problems with the proxy settings).

Error value

Description

hex

Reserved

hex

A TCP/IP error occurred during sending or receiving.

hex

A TCP/IP error occurred during sending or receiving.

Error value

Description

hex

Reserved

hex

Internal error 1

hex

Too little free memory space available.

hex

An internal handle is invalid.

hex

An error occurred while the HTTP application was being executed.

hex

An internal parameter is invalid.

hex

An internal parameter is invalid.

hex

An internal parameter is invalid.

hex

Too little free memory space available.

hex

Too little free memory space available.

hex

Too little free memory space available.

Содержание POSIDYN SDS 5000





































































































































































































Результаты поиска

Содержание POSIDYN SDS 5000

Отзывы:

Похожие инструкции для POSIDYN SDS 5000

Бренды по названию

Популярные бренды

Stober POSIDYN SDS 5000, Руководство по эксплуатации

Результаты поиска

Содержание POSIDYN SDS 5000

Отзывы:

Похожие инструкции для POSIDYN SDS 5000

Бренды по названию

Популярные бренды