manualshive.com logo in svg

ST STM32F101xx series, Справочное руководство, Страница: 935 / 1096

Поделиться
Скачать
ST STM32F101xx series Скачать руководство пользователя страница 935

RM0008

USB on-the-go full-speed (OTG_FS)

Doc ID 13902 Rev 12

935/1096

   

   

   

A-device host negotiation protocol

HNP switches the USB host role from the A-device to the B-device. The application must set 
the HNP-capable bit in the Core USB configuration register to enable the OTG_FS controller 
to perform HNP as an A-device.

Figure 323. A-device HNP

1.

DPPULLDOWN = signal from core to PHY to enable/disable the pull-down on the DP line inside the PHY.
DMPULLDOWN = signal from core to PHY to enable/disable the pull-down on the DM line inside the PHY.

1.

The OTG_FS controller sends the B-device a SetFeature b_hnp_enable descriptor to 
enable HNP support. The B-device’s ACK response indicates that the B-device 
supports HNP. The application must set host Set HNP Enable bit in the OTG Control 
and status register to indicate to the OTG_FS controller that the B-device supports 
HNP.

2. 

When it has finished using the bus, the application suspends by writing the Port 
suspend bit in the host port control and status register.

3. 

When the B-device observes a USB suspend, it disconnects, indicating the initial 
condition for HNP. The B-device initiates HNP only when it must switch to the host role; 
otherwise, the bus continues to be suspended.

The OTG_FS controller sets the host negotiation detected interrupt in the OTG 
interrupt status register, indicating the start of HNP.

The OTG_FS controller deasserts the DM pull down and DM pull down in the PHY to 
indicate a device role. The PHY enables the OTG_FS_DP pull-up resistor to indicate a 
connect for B-device.

The application must read the current mode bit in the OTG Control and status register 
to determine device mode operation.

4. 

The B-device detects the connection, issues a USB reset, and enumerates the 
OTG_FS controller for data traffic.

5. 

The B-device continues the host role, initiating traffic, and suspends the bus when 
done.

The OTG_FS controller sets the early suspend bit in the Core interrupt register after 3 
ms of bus idleness. Following this, the OTG_FS controller sets the USB Suspend bit in 
the Core interrupt register.

a

i156

83

OTG core

DP

DM

DPPULLDOWN

DMPULLDOWN

Ho

s

t

Device

Ho

s

t

1

Sus

pend 2

3

4

5

Re

s

et

6

Tr

a

ffic

7

8

Connect

Tr

a

ffic

Содержание STM32F101xx series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов