manualshive.com logo in svg

ST STM32F101xx series, Справочное руководство, Страница: 922 / 1096

Поделиться
Скачать
ST STM32F101xx series Скачать руководство пользователя страница 922

   

   

   

USB on-the-go full-speed (OTG_FS)

RM0008

922/1096

 Doc ID 13902 Rev 12

(IISOOXFRM in OTG_FS_GINTSTS), indicating that an XFRC interrupt (in 
OTG_FS_DOEPINTx) is not asserted on at least one of the isochronous OUT 
endpoints. At this point, the endpoint with the incomplete transfer remains enabled, but 
no active transfers remain in progress on this endpoint on the USB.

Application programming sequence:

1.

Asserting the IISOOXFRM interrupt (OTG_FS_GINTSTS) indicates that in the current 
frame, at least one isochronous OUT endpoint has an incomplete transfer.

2. 

If this occurs because isochronous OUT data is not completely emptied from the 
endpoint, the application must ensure that the application empties all isochronous OUT 
data (data and status) from the receive FIFO before proceeding.

–

When all data are emptied from the receive FIFO, the application can detect the 
XFRC interrupt (OTG_FS_DOEPINTx). In this case, the application must re-
enable the endpoint to receive isochronous OUT data in the next frame.

3. 

When it receives an IISOOXFRM interrupt (in OTG_FS_GINTSTS), the application 
must read the control registers of all isochronous OUT endpoints 
(OTG_FS_DOEPCTLx) to determine which endpoints had an incomplete transfer in the 
current microframe. An endpoint transfer is incomplete if both the following conditions 
are met:

–

EONUM bit (in OTG_FS_DOEPCTLx) = SOFFN[0] (in OTG_FS_DSTS)

–

EPENA = 1 (in OTG_FS_DOEPCTLx)

4. 

The previous step must be performed before the SOF interrupt (in OTG_FS_GINTSTS) 
is detected, to ensure that the current frame number is not changed.

5. 

For isochronous OUT endpoints with incomplete transfers, the application must discard 
the data in the memory and disable the endpoint by setting the EPDIS bit in 
OTG_FS_DOEPCTLx.

6. 

Wait for the EPDIS interrupt (in OTG_FS_DOEPINTx) and enable the endpoint to 
receive new data in the next frame.

–

Because the core can take some time to disable the endpoint, the application may 
not be able to receive the data in the next frame after receiving bad isochronous 
data.

●

Stalling a non-isochronous OUT endpoint

This section describes how the application can stall a non-isochronous endpoint.

1.

Put the core in the Global OUT NAK mode.

2. 

Disable the required endpoint

–

When disabling the endpoint, instead of setting the SNAK bit in 
OTG_FS_DOEPCTL, set STALL = 1 (in OTG_FS_DOEPCTL).

The STALL bit always takes precedence over the NAK bit.

3. 

When the application is ready to end the STALL handshake for the endpoint, the STALL 
bit (in OTG_FS_DOEPCTLx) must be cleared.

4. 

If the application is setting or clearing a STALL for an endpoint due to a 
SetFeature.Endpoint Halt or ClearFeature.Endpoint Halt command, the STALL bit must 
be set or cleared before the application sets up the Status stage transfer on the control 
endpoint.

Содержание STM32F101xx series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов