manualshive.com logo in svg

ST STM32F101xx series, Справочное руководство, Страница: 784 / 1096

Поделиться
Скачать
ST STM32F101xx series Скачать руководство пользователя страница 784

   

   

   

Universal synchronous asynchronous receiver transmitter (USART)

RM0008

784/1096

 Doc ID 13902 Rev 12

Figure 292. Parity error detection using the 1.5 stop bits

The USART can provide a clock to the smartcard through the CK output. In smartcard 
mode, CK is not associated to the communication but is simply derived from the internal 
peripheral input clock through a 5-bit prescaler. The division ratio is configured in the 
prescaler register USART_GTPR. CK frequency can be programmed from f

CK

/2 to f

CK

/62, 

where f

CK

 is the peripheral input clock.

27.3.12 

IrDA SIR ENDEC block 

The IrDA mode is selected by setting the IREN bit in the USART_CR3 register. In IrDA 
mode, the following bits must be kept cleared:

●

LINEN, STOP and CLKEN bits in the USART_CR2 register,

●

SCEN and HDSEL bits in the USART_CR3 register.

The IrDA SIR physical layer specifies use of a Return to Zero, Inverted (RZI) modulation 
scheme that represents logic 0 as an infrared light pulse (see 

Figure 293

).

The SIR Transmit encoder modulates the Non Return to Zero (NRZ) transmit bit stream 
output from USART. The output pulse stream is transmitted to an external output driver and 
infrared LED. USART supports only bit rates up to 115.2Kbps for the SIR ENDEC. In normal 
mode the transmitted pulse width is specified as 3/16 of a bit period.

The SIR receive decoder demodulates the return-to-zero bit stream from the infrared 
detector and outputs the received NRZ serial bit stream to USART. The decoder input is 
normally HIGH (marking state) in the idle state. The transmit encoder output has the 
opposite polarity to the decoder input. A start bit is detected when the decoder input is low.

1 bit time

1.5 bit time

0.5 bit time

1 bit time

sampling at

8th, 9th, 10th

sampling at

8th, 9th, 10th

sampling at

8th, 9th, 10th

sampling at

16th, 17th, 18th

Bit 7

Parity Bit

1.5 Stop Bit

Содержание STM32F101xx series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов