manualshive.com logo in svg

ST STM32F101xx series, Справочное руководство, Страница: 858 / 1096

Поделиться
Скачать
ST STM32F101xx series Скачать руководство пользователя страница 858

   

   

   

USB on-the-go full-speed (OTG_FS)

RM0008

858/1096

 Doc ID 13902 Rev 12

Bit 6

PRES:

 Port resume

The application sets this bit to drive resume signaling on the port. The core continues to drive 
the resume signal until the application clears this bit.

If the core detects a USB remote wakeup sequence, as indicated by the Port resume/remote 
wakeup detected interrupt bit of the Core interrupt register (WKUINT bit in 
OTG_FS_GINTSTS), the core starts driving resume signaling without application intervention 
and clears this bit when it detects a disconnect condition. The read value of this bit indicates 
whether the core is currently driving resume signaling.

0: No resume driven
1: Resume driven

Bit 5

POCCHNG:

 Port overcurrent change

The core sets this bit when the status of the Port overcurrent active bit (bit 4) in this register 
changes.

Bit 4

POCA:

 Port overcurrent active

Indicates the overcurrent condition of the port.

0: No overcurrent condition
1: Overcurrent condition

Bit 3

PENCHNG:

 Port enable/disable change

The core sets this bit when the status of the Port enable bit [2] in this register changes.

Bit 2

PENA:

 Port enable

A port is enabled only by the core after a reset sequence, and is disabled by an overcurrent 
condition, a disconnect condition, or by the application clearing this bit. The application cannot 
set this bit by a register write. It can only clear it to disable the port. This bit does not trigger 
any interrupt to the application.

0: Port disabled
1: Port enabled

Bit 1

PCDET:

 Port connect detected

The core sets this bit when a device connection is detected to trigger an interrupt to the 
application using the host port interrupt bit in the Core interrupt register (HPRTINT bit in 
OTG_FS_GINTSTS). The application must write a 1 to this bit to clear the interrupt.

Bit 0

PCSTS:

 Port connect status

0: No device is attached to the port
1: A device is attached to the port

Содержание STM32F101xx series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов