manualshive.com logo in svg

ST STM32F101xx series, Справочное руководство, Страница: 674 / 1096

Поделиться
Скачать
ST STM32F101xx series Скачать руководство пользователя страница 674

   

   

   

Serial peripheral interface (SPI)

RM0008

674/1096

 Doc ID 13902 Rev 12

25 

Serial peripheral interface (SPI)

Low-density

 

devices

 are STM32F101xx, STM32F102xx and STM32F103xx 

microcontrollers where the Flash memory density ranges between 16 and 32 Kbytes.

Medium-density

 

devices

 are STM32F101xx, STM32F102xx and STM32F103xx 

microcontrollers where the Flash memory density ranges between 64 and 128 Kbytes.

High-density devices

 are STM32F101xx and STM32F103xx microcontrollers where the 

Flash memory density ranges between 256 and 512 Kbytes.

XL-density devices

 are STM32F101xx and STM32F103xx microcontrollers where the 

Flash memory density ranges between 768 Kbytes and 1 Mbyte.

Connectivity line devices

 are STM32F105xx and STM32F107xx microcontrollers.

25.1 SPI 

introduction

In high-density, XL-density and connectivity line devices, the SPI interface gives the 
flexibility to get either the SPI protocol or the I

2

S audio protocol. By default, it is the SPI 

function that is selected. It is possible to switch the interface from SPI to I

2

S by software. 

In low- and medium-density devices, the I

2

S protocol is not available.

The serial peripheral interface (SPI) allows half/ full-duplex, synchronous, serial 
communication with external devices. The interface can be configured as the master and in 
this case it provides the communication clock (SCK) to the external slave device. The 
interface is also capable of operating in multimaster configuration.

It may be used for a variety of purposes, including Simplex synchronous transfers on two 
lines with a possible bidirectional data line or reliable communication using CRC checking.

I

2

S is also a synchronous, serial communication interface with a 3-pin protocol. It can 

address four different audio standards including the I

2

S Phillips standard, the MSB- and 

LSB-justified standards and the PCM standard. It can operate in slave or master mode with 
half-duplex communication. Master clock may be provided by the interface to an external 
slave component when the I

2

S is configured as the communication master.

Warning:

Since some SPI3/I2S3 pins are shared with JTAG pins 
(SPI3_NSS/I2S3_WS with JTDI and SPI3_SCK/I2S3_CK with 
JTDO), they are not controlled by the IO controller and are 
reserved for JTAG usage (after each Reset).
For this purpose, prior to configure the SPI3/I2S3 pins, the 
user has to disable the JTAG and use the SWD interface 
(when debugging the application), or disable both JTAG/SWD 
interfaces (for standalone applications). For more 
information on the configuration of JTAG/SWD interface pins, 
please refer to 

Section 9.3.5: JTAG/SWD alternate function 

remapping

.

Содержание STM32F101xx series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов