manualshive.com logo in svg

ST STM32F101xx series, Справочное руководство, Страница: 924 / 1096

Поделиться
Скачать
ST STM32F101xx series Скачать руководство пользователя страница 924

   

   

   

USB on-the-go full-speed (OTG_FS)

RM0008

924/1096

 Doc ID 13902 Rev 12

IN data transfers

●

Packet write

This section describes how the application writes data packets to the endpoint FIFO when 
dedicated transmit FIFOs are enabled.

1.

The application can either choose the polling or the interrupt mode.

–

In polling mode, the application monitors the status of the endpoint transmit data 
FIFO by reading the 

OT

G_FS_DTXFSTSx register, to determine if there is enough 

space in the data FIFO.

–

In interrupt mode, the application waits for the TXFE interrupt (in 
OTG_FS_DIEPINTx) and then reads the OTG_FS_DTXFSTSx register, to 
determine if there is enough space in the data FIFO.

–

To write a single non-zero length data packet, there must be space to write the 
entire packet in the data FIFO.

–

To write zero length packet, the application must not look at the FIFO space.

2. 

Using one of the above mentioned methods, when the application determines that 
there is enough space to write a transmit packet, the application must first write into the 
endpoint control register, before writing the data into the data FIFO. Typically, the 
application, must do a read modify write on the OTG_FS_DIEPCTLx register to avoid 
modifying the contents of the register, except for setting the Endpoint Enable bit.

The application can write multiple packets for the same endpoint into the transmit FIFO, if 
space is available. For periodic IN endpoints, the application must write packets only for one 
microframe. It can write packets for the next periodic transaction only after getting transfer 
complete for the previous transaction.

●

Setting IN endpoint NAK

Internal data flow:

1.

When the application sets the IN NAK for a particular endpoint, the core stops 
transmitting data on the endpoint, irrespective of data availability in the endpoint’s 
transmit FIFO.

2. 

Non-isochronous IN tokens receive a NAK handshake reply

–

Isochronous IN tokens receive a zero-data-length packet reply

3. 

The core asserts the INEPNE (IN endpoint NAK effective) interrupt in 
OTG_FS_DIEPINTx in response to the SNAK bit in OTG_FS_DIEPCTLx.

4. 

Once this interrupt is seen by the application, the application can assume that the 
endpoint is in IN NAK mode. This interrupt can be cleared by the application by setting 
the CNAK bit in OTG_FS_DIEPCTLx.

Application programming sequence:

Содержание STM32F101xx series









































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов