Siemens SINUMERIK ONE NCU 1740 Скачать руководство пользователя страница 90

Страница: 90 / 164

7-segment display

Meaning

Troubleshooting

SD Error <n>

<n> = single-digit code:
• SD Error 1: System card reader is

not present in HW info

• SD Error 2: Card reader not re‐

sponding; HW problem

• SD Error 3: SD card missing, or

does not contain an ext4 partition

• SD Error 4: fsck (file system check)

failed with incorrigible errors

• SD Error 5: File system linking

failed

A write or read error has occurred on
the SD card.

• Check whether the mechanical write protection (lock) of

the SD card has been activated.

• It is possible that the SD card is defective and must be

replaced.

• Check the SD card using the "Check storage integrity" di‐

agnostics option.

SIGErr=<nn>

<nn> = double-digit code:

SIGErr=08: signature file error

No SIEMENS signature was found for
a software component.

Check whether the original CNC software package is installed
and has not been modified.
• Install the original CNC software package.

SIGErr=09: Device certificate period
of validity error

The system time has not been cor‐
rectly set.

Occurs the first time the device is turned on if the system time
has not yet been set.
Check the settings if the error is permanent.

SIGErr=11: signature file invalid

Software was installed with an unas‐
sociated signature file.

Check whether the original CNC software package is installed
and has not been modified.
• Install the original CNC software package.

All others SIGErr

The hardware is possibly defective.
• Contact SIEMENS Technical Support.

unPAC FAIL

A problem has occurred when read‐
ing, unzipping or writing the data.

Boot the NCU using the SINUMERIK service system, and check
the partition using the "Check storage integrity" diagnostics
option.
• Contact SIEMENS Technical Support if the diagnostics

check is unsuccessful.

The archive with the CNC software is
possibly corrupt or unreadable.

Reinstall the CNC software if the SD card is OK.

point not flashing: Operating system
has crashed where the NCK is no lon‐
ger clocking

Restart the NCU.

Please contact SIEMENS Technical Support (Page 10) if it was not possible to resolve the error.

Diagnostics
9.1 Error messages

NCU 1740

Equipment Manual, 10/2021, A5E51087503B AA

Содержание SINUMERIK ONE NCU 1740





































































































































































Результаты поиска

Содержание SINUMERIK ONE NCU 1740

Отзывы:

Похожие инструкции для SINUMERIK ONE NCU 1740

Бренды по названию

Популярные бренды

Siemens SINUMERIK ONE NCU 1740, Руководство по эксплуатации оборудования

Результаты поиска

Содержание SINUMERIK ONE NCU 1740

Отзывы:

Похожие инструкции для SINUMERIK ONE NCU 1740

Бренды по названию

Популярные бренды