Siemens SINUMERIK ONE NCU 1740 Скачать руководство пользователя страница 36

Страница: 36 / 164

Meaning of the RDY, COM, DIAG and SD Activity NCU LEDs

Name

Function

Status

Meaning

RDY

Ready

LED lights up red

There is at least one fault (e.g. RESET, watchdog monitoring etc.) or
the NCU is ramping up.

LED flashes red (2 Hz)

Not assigned (SINAMICS boot error).

LED lights up yellow

Ramping up the NCU.

LED flashes yellow

(0.5 Hz)

Firmware update of the connected DRIVE-CLiQ components

LED flashes yellow (2 Hz)

Firmware update is complete for components. Wait for POWER ON
for the components in question.

LED lights up green

NC ramped up and everything in cyclic mode

LED flashes

green/orange or

red/orange (1 Hz)

LED-supported detection of connected DRIVE-CLiQ component is
activated: (p0124[0] = 1).

COM

Communi‐

cation

LED off

CP not ramped up / started

LED lights up green

Communication via CP possible (RUN operating state)

LED flashes green

Communication possible (no configuration)

LED lights up yellow

CP was stopped via PLC/TIA. No communication.

LED flashes yellow

Configuration received and transition to the RUN operating state.

LED flashes red

Error status (FATAL error)

Description
4.4 Operator control and display elements

NCU 1740

Equipment Manual, 10/2021, A5E51087503B AA

Содержание SINUMERIK ONE NCU 1740





































































































































































Результаты поиска

Содержание SINUMERIK ONE NCU 1740

Отзывы:

Похожие инструкции для SINUMERIK ONE NCU 1740

Бренды по названию

Популярные бренды

Siemens SINUMERIK ONE NCU 1740, Руководство по эксплуатации оборудования

Результаты поиска

Содержание SINUMERIK ONE NCU 1740

Отзывы:

Похожие инструкции для SINUMERIK ONE NCU 1740

Бренды по названию

Популярные бренды