Siemens SINUMERIK ONE NCU 1740 Скачать руководство пользователя страница 91

Страница: 91 / 164

Service and maintenance

10.1

Service and maintenance

Cleaning the device

The device is designed for low-maintenance operation. Nevertheless, you must regularly clean
the device.

Note
Switch the device off for cleaning

Clean the device only when it is switched off.

For cleaning, use a soft cloth moistened either with water or a mild cleaning agent. Use only
dishwashing detergent or foaming detergent.

Procedure
Spray the cleaning agent on to a cleaning cloth. Never use caustic solvents or abrasive cleaners.

Note
Avoid damage

Do not clean the device using compressed air or steam jets because they can damage it.

Checking the device

In order to prevent foreign bodies or liquids entering the device, regularly check the device for
the following:

• Ensure that all the housing screws are in place and tight

• For damage to the housing

• For damage to the cable cover or cable entry

Protect the device from environmental effects

Protect the device against the following environmental factors:

• Direct sunshine and heat sources

• Mechanical vibration and shock

• Dust

• Humidity

• Strong magnetic fields

NCU 1740
Equipment Manual, 10/2021, A5E51087503B AA

Содержание SINUMERIK ONE NCU 1740





































































































































































Результаты поиска

Содержание SINUMERIK ONE NCU 1740

Отзывы:

Похожие инструкции для SINUMERIK ONE NCU 1740

Бренды по названию

Популярные бренды

Siemens SINUMERIK ONE NCU 1740, Руководство по эксплуатации оборудования

Результаты поиска

Содержание SINUMERIK ONE NCU 1740

Отзывы:

Похожие инструкции для SINUMERIK ONE NCU 1740

Бренды по названию

Популярные бренды