Siemens SINUMERIK ONE NCU 1740 Скачать руководство пользователя | Manualshive

Страница: 64 / 164

background image

8.5.2

Requirements for the power supply

External 24 V power supply

Power is supplied to the NCU by an external 24 V power supply (e.g.: SITOP). The following
power consumption values for an NCU provide a configuration basis for calculating the 24 VDC
power supply.

Table 8-3

Input voltage specification

Typ. current consumption

1)

Max. power consumption

2)

0.65 A

11.1 A

1)

NCU only (processor, memory, etc.)

2)

NCU with full load at all outputs (digital outputs, USB, DRIVE-CLiQ, PROFIBUS DP, etc.)

Requirements of DC power supplies

WARNING

Electric shock as a result of an unsafe DC power supply

If an unsafe DC power supply is connected, exposed components may be at a hazardous
voltage level, which can result in serious injury or death.
• As DC power supply, use a Category PELV/DVC A circuit according to EN 61010-1.

WARNING

Electric shock due to inadequately protected power supply cables

If power supply cables are inadequately protected, then lightning strikes can result in a surge
voltage. This can result in death, serious injury and material damage.

In the case of supply lines > 10 m, protectors must be installed at the device input in order to
protect against lightning (surge).

The DC power supply must be connected to the ground/shield of the NCU for EMC and/or
functional reasons. For EMC reasons, this connection should only be made at one point. This
connection is normally provided as standard in the S7-1500 I/Os. In exceptional circumstances
when this is not the case, the ground connection should be made on the grounding rail of the
control cabinet; please also refer to /EMC/EMC Installation Guide.

Table 8-4

DC power supply requirements according to EN 61131-2

Rated voltage

24 V DC

Voltage range (average value)

20.4 VDC to 28.8 VDC

Voltage ripple peak-to-peak

5% (unfiltered 6-pulse rectification)

Ramp-up time at POWER ON

Any

Non-periodic overvoltages

≤ 35 V

Connecting
8.5 Power supply

NCU 1740

64

Equipment Manual, 10/2021, A5E51087503B AA

«
...
62
63
64
65
66
...
»

Содержание SINUMERIK ONE NCU 1740





































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SINUMERIK ONE NCU 1740

AF-600 FP Series

Бренд: GE Страницы: 7

Бренд: Jafar Страницы: 9

Бренд: Parker Страницы: 30

Бренд: VAT Страницы: 22

Бренд: GE Страницы: 425

Бренд: FAAC Страницы: 32

Бренд: Federal Signal Corporation Страницы: 79

Бренд: Federal Signal Corporation Страницы: 32

Elemec3 013-02-0095-002

Бренд: GAI-Tronics Страницы: 12

Grafica DNE-K07

Бренд: Paradox Страницы: 24

Бренд: Panosol Страницы: 105

Бренд: Pangolin Страницы: 8

Бренд: Samson Страницы: 56

Бренд: EasyIO Страницы: 17

Бренд: Purmo Страницы: 2

Бренд: salmson Страницы: 78

Бренд: D+H Страницы: 16

Бренд: TWR Lighting Страницы: 49

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды