manualshive.com logo in svg

Siemens SINUMERIK 808D, Руководство по диагностике

Поделиться
Скачать
Siemens SINUMERIK 808D Скачать руководство пользователя страница 85

6540

Too many directories in the NC memory

Explanation:

The number of directories in the NC file system (part of the NC memory) has reached the maximum limit.

Reaction:

Alarm display.

Remedy:

- Delete or unload directory (e.g. workpiece), or
- Increase MD18310 $MN_MM_NUM_DIR_IN_FILESYSTEM.

Programm 

continuation:

Clear alarm with the Delete key or NC START.

6550

Too many subdirectories

Explanation:

The number of subdirectories in a directory of the NCK has reached the maximum limit.

Reaction:

Alarm display.

Remedy:

Please inform the authorized personnel/service department.
- Delete or empty subdirectories in the respective directory, or
- Increase MD18270 $MN_MM_NUM_SUBDIR_PER_DIR.

Programm 

continuation:

Clear alarm with the Delete key or NC START.

6560

Data format not allowed

Explanation:

An attempt was made to write impermissible data in an NCK file. This error can occur in particular when the attempt was 

made to load binary data in the NCK as ASCII file.
The error can also occur during preprocessing of cycles (see MD10700 $MN_PREPROCESSING_LEVEL) if the NC block 

is very long. In this case, subdivide the NC block.

Reaction:

Alarm display.

Remedy:

Specify that the file concerned is a binary file (e.g. extension: .BIN).

Programm 

continuation:

Clear alarm with the Delete key or NC START.

6568

EES memory limit on the CF card reached

Explanation:

The memory space assigned to EED on the CF card is exhausted.

Reaction:

NC Start disable in this channel.
Alarm display.

Remedy:

Delete files on the CF card

Programm 

continuation:

Switch control OFF - ON.

6569

HMI user memory limit reached on the CF card.

Explanation:

The memory space in the user area assured on the CF card is exhausted.

Reaction:

NC Start disable in this channel.
Alarm display.

Remedy:

Delete files on the CF card

Programm 

continuation:

Switch control OFF - ON.

6570

NC memory full

Explanation:

The NC card file system of the NCK is full. The task cannot be executed. Too many system files were created in the DRAM.

Reaction:

Alarm display.

Remedy:

Start fewer "execute from external" processes.

Programm 

continuation:

Clear alarm with the Delete key or NC START.

SINUMERIK 808D ADVANCED alarms

5.2 NCK alarms

Diagnostics Manual

Diagnostics Manual, 06/2015, 6FC5398-6DP10-0BA2

85

Содержание SINUMERIK 808D























































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды