Senlan SB200 Series Скачать руководство пользователя страница 36

Страница: 36 / 181

Inverter Operation and Trial Operation

7. Parameters on Motor Nameplate: Rated power, number of poles, rated current and rated rotation

speed. Refer to Page 51 for details.

8. Motor Overload Protection: For details, refer to Fb-00: Motor Heat Dissipation Conditions, Fb-01:

“Motor Overload Protection Value” and Fb-02: Motor Overload Protection Action Options.

For details about optimized settings, refer to the following tips:

1. F2-00: V/F Curve Settings on Page 48.

2. F2-01: Torque Elevation Options on Page 48.

3. F2-09: “Vibration Dampening” on Page 49. This function is used to eliminate motor vibrations under

a light load. If the motor vibrates, adjust the parameter from by stepping up the values until the

vibration is eliminated. The parameter value must not be too great.

4. F2-02: Amplitude of Manual Toque Elevation on Page 48. If the starting current is too great, you

may reduce the parameter value.

5. Auto Torque Elevation. To increase the starting torque and output torque (in low-speed operation) of

the inverter, auto torque elevation is recommended (F2-01: Torque Elevation Options =2).

6. Slip Compensation on Page 49. Slip compensation can reduce a fall in speed caused by loads. This

function is not enabled unless auto torque elevation is enabled. The following settings are required:

F2-05: “Slip Compensation Gain”, F2-06: “Filter Time of Slip Compensation” and F2-07 and F2-08:

Clipping of Slip Compensation

Содержание SB200 Series






















































































































































































Результаты поиска

Содержание SB200 Series

Отзывы:

Бренды по названию

Популярные бренды

Senlan SB200 Series, Руководство пользователя

Результаты поиска

Содержание SB200 Series

Отзывы:

Бренды по названию

Популярные бренды