manualshive.com logo in svg

Segway SE-3 Patroller, Руководство по обслуживанию


Поделиться
Скачать
background image

SE-3 Patroller

88

Elastomer Bushing & Drive Hub

Check to see if the Elastomer Bushing is worn or damaged. 
Presence of excessive particles of elastomer material indicates 
that replacement is necessary.

Tools Required:

  Cotton swab

 

 

Molykote G-n paste

Removal

1.  Make sure the SE-3 Patroller is powered off, 

unplugged, and the parking brake is engaged.

2.  Remove the following components:

a.  Battery Module (

page 8

)

b.  Storage Trays (

page 13

)

c.  Bib Panel (

page 14

)

d.  Fender (

page 22

)

e.  Rear Tire/Wheel (

page 30

)

f.  Rear Caliper & Rotor (

page 62

)

g.  Gearbox (

page 86

)

3.  Pull the Drive Hub off the Motor.
4.  Pull the Elastomer Bushing off of the Drive Hub 

(

Figure 119

).

Installation

1.  Make sure the SE-3 Patroller is powered off, 

unplugged, and the parking brake is engaged.

2.  Orient the Elastomer Bushing with the tabs toward 

the Drive Hub.

3.  Slide the Elastomer Bushing onto the Drive Hub.
4.  Use a cotton swab to spread some Molykote G-n 

paste (P/N 24505-00001) on the splines inside the 
Drive Hub. This paste helps reduce wear between the 
Drive Hub and the Motor.

5.  Slide the Drive Hub onto the Motor.
6.  Install the following components:

a.  Gearbox (

page 86

)

b.  Rear Caliper & Rotor (

page 62

)

c.  Rear Tire/Wheel (

page 30

)

d.  Fender (

page 22

)

e.  Bib Panel (

page 14

)

f.  Storage Trays (

page 13

)

g.  Battery Module (

page 8

)

7.  Perform post-service tests (

page 127

).

Figure 119:  Elastomer Bushing

Elastomer Bushing

(21091-00001)

Drive Hub

(24008-00001)

Drive Train

Содержание SE-3 Patroller





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для SE-3 Patroller

ECAR GOLF Sightseeing Bus Manual preview
Sightseeing Bus
Бренд: ECAR GOLF Страницы: 21

Бренды по названию

Популярные бренды

Загрузить еще бренды