manualshive.com logo in svg

Segway SE-3 Patroller, Руководство по обслуживанию

Поделиться
Скачать
Segway SE-3 Patroller Скачать руководство пользователя страница 120

SE-3 Patroller

112

Figure 151:  Handlebar Controls Harness to PI Board

Figure 152:  Connectors on Steering Column

Handlebar Controls Harness

This harness connects the PI Board to the Control Cluster, 
Headlight, Throttle, and both Brake Levers.

Tools Required:

  Wire cutters

Removal

1.  Make sure the SE-3 Patroller is powered off, 

unplugged, and the parking brake is engaged.

2.  Remove the following components:

a.  Battery Module (

page 8

)

b.  Storage Trays (

page 13

)

c.  Bib Panel (

page 14

)

d.  Glove Box (

page 16

)

e.  Front Cowl (

page 17

)

f.  Electronics Shield (

page 100

)

3.  Disconnect the wire harness from the PI Board. 

See 

Figure 151

.

4.  Disconnect the wire harness from the Control Cluster, 

Headlight, Throttle, and both Brake Levers. 
See 

Figure 152

.

5.  Using a pair of wire cutters, remove three cable ties:

a.  This harness to the frame.
b.  This harness to the User Interface Harness.
c.  Harnesses on the steering column.

6.  Remove the Handlebar Controls Harness.

Left 

Brake Lever

Right 

Brake Lever

Headlight

Throttle

Control 

Cluster

Handle Bar

Harnesses

Содержание SE-3 Patroller





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды