manualshive.com logo in svg

Segway SE-3 Patroller, Руководство по обслуживанию


Поделиться
Скачать
background image

Service Manual

111

Installation

1.  Make sure the SE-3 Patroller is powered off, 

unplugged, and the parking brake is engaged.

2.  Connect the Drive Harness to the Motor Controller.
3.  Connect the Drive Harness to the Motor.
4.  Feed the harness through the hole in the front of the 

motor cavity. Send the Left Drive Harness out the left 
side of the frame. Send the Right Drive Harness out 
the right side of the frame.

5.  Feed the harness under the horizontal brace on 

the frame (see 

Figure 150

) and connect it to the PI 

Board.

6.  Install two cable ties around the harnesses in the 

motor cavity.

7.  Install two cable ties around the harnesses on the 

side of the frame.

8.  Install the following components:

a.  Motor Cavity Lid (

page 89

)

b.  Rider Detect Mat (

page 82

)

c.  Electronics Shield (

page 100

)

d.  Side Panel (

page 20

)

e.  Light Cluster (

page 18

)

f.  Front Cowl (

page 17

)

g.  Glove Box (

page 16

)

h.  Bib Panel (

page 14

)

i. 

Storage Trays (

page 13

)

j. 

Battery Module (

page 8

)

9.  Perform post-service tests (

page 127

).

Harnesses

Figure 150:  Drive Harness Routing

Brace

Содержание SE-3 Patroller





















































































































































Отзывы:

Нет отзывов

Похожие инструкции для SE-3 Patroller

Toro Workman GTX Service Manual preview
Workman GTX
Бренд: Toro Страницы: 187

Бренды по названию

Популярные бренды

Загрузить еще бренды