Segway SE-3 Patroller Скачать руководство пользователя страница 21

Страница: 21 / 148

Service Manual

Storage Tray

The Storage Tray is the first component to remove when
removing body panels. Both Storage Trays must be removed
before removing the Bib Panel.

Tools Required:

4 mm hex wrench

Torque

wrench

Removal

1. Make sure the SE-3 Patroller is powered off,

unplugged, and the parking brake is engaged.

2. Using a 4 mm hex wrench, remove the fastener at the

bottom of the Storage Tray.

3. Remove the Storage Tray.

Installation

1. Make sure the SE-3 Patroller is powered off,

unplugged, and the parking brake is engaged.

2. Insert the Storage Tray and line up the hole in the

bottom of the Storage Tray with the threaded hole in
the vehicle’s frame.

3. Using a 4 mm hex wrench, install the fastener.

Torque to

1.0 N-m (0.74 ft-lbf)

. Do not over-tighten.

24270-00006

1.0 N-m (0.74 ft-lbf)

Storage Tray

Left 23758-00001

Right 23759-00001

Figure 6: Storage Tray

Body Panels

Содержание SE-3 Patroller





















































































































































Результаты поиска

Содержание SE-3 Patroller

Отзывы:

Похожие инструкции для SE-3 Patroller

Бренды по названию

Популярные бренды

Segway SE-3 Patroller, Руководство по обслуживанию

Результаты поиска

Содержание SE-3 Patroller

Отзывы:

Похожие инструкции для SE-3 Patroller

Бренды по названию

Популярные бренды