Segway SE-3 Patroller Скачать руководство пользователя страница 122

Страница: 122 / 148

SE-3 Patroller

114

Figure 154: UI Harness to PI Board

Figure 155: Harness to UI Board

User Interface Harness

This harness connects the PI Board and the UI Module.

Tools Required:

Wire cutters

Removal

1. Make sure the SE-3 Patroller is powered off,

unplugged, and the parking brake is engaged.

2. Remove the following components:

a. Battery Module (

page 8

)

b. Storage Trays (

page 13

)

c. Bib Panel (

page 14

)

d. Glove Box (

page 16

)

e. Front Cowl (

page 17

)

f. Electronics Shield (

page 100

)

g. UI Module (

page 70

)

3. Disconnect the wire harness from the PI Board.

See

Figure 154

4. Disconnect the wire harness from the UI Board.

See

Figure 155

5. Using wire cutters, remove four cable ties:

a. Two holding the harness to the steering

column.

b. One connecting this harness to the

Handlbar Controls Harness.

c. One connecting the harness to the frame.

6. Carefully push the rubber grommet out of the hole in

the back of the UI Housing. See

Figure 156

NOTICE

Do not use any sharp or pointed tools. You could
puncture the grommet, thereby allowing water to
enter the UI Housing.

7. Remove the User Interface Harness.

User

Interface

Harnesses

Содержание SE-3 Patroller





















































































































































Результаты поиска

Содержание SE-3 Patroller

Отзывы:

Бренды по названию

Популярные бренды

Segway SE-3 Patroller, Руководство по обслуживанию

Результаты поиска

Содержание SE-3 Patroller

Отзывы:

Бренды по названию

Популярные бренды