Segway SE-3 Patroller Скачать руководство пользователя страница 84

Страница: 84 / 148

SE-3 Patroller

Handlebar Grip

The Handlebar Grip does not slide off easily. To remove it, you
will have to cut it off the handlebar.

Tools Required:

Cutting tool (box cutter or utility knife)

Removal

1. Make sure the SE-3 Patroller is powered off,

unplugged, and the parking brake is engaged.

2. Score the Handlebar Grip with a cutting tool.

CAUTION!

Be careful not to cut yourself with the sharp blade.

3. Grab the Handlebar Grip near the flange and tear it at

the score line you created.

4. Tear the Handlebar Grip and pull it off the handlebar.

Installation

1. Make sure the SE-3 Patroller is powered off,

unplugged, and the parking brake is engaged.

2. Slide the end of the Handlebar Grip onto the left

handlebar. See

Figure 107

3. Press the palm of your hand onto the end of the

Handlebar Grip. Push the Handlebar Grip onto the
handlebar until it is fully seated.

NOTICE

Do not twist the Handlebar Grip when installing it.

Figure 107: Handlebar Grip

Handlebar Grip
(23807-00001)

Controls

Содержание SE-3 Patroller





















































































































































Результаты поиска

Содержание SE-3 Patroller

Отзывы:

Бренды по названию

Популярные бренды

Segway SE-3 Patroller, Руководство по обслуживанию

Результаты поиска

Содержание SE-3 Patroller

Отзывы:

Бренды по названию

Популярные бренды