Segway SE-3 Patroller Скачать руководство пользователя страница 52

Страница: 52 / 148

SE-3 Patroller

Battery Slides

The Battery Slides orient the Battery Module in the frame.
They also allow the Battery Module to slide smoothly when
being installed or removed.

Tools Required:

2.5 mm hex wrench

Torque

wrench

Removal

1. Make sure the SE-3 Patroller is powered off,

unplugged, and the parking brake is engaged.

2. Remove the Battery Module (

page 8

3. Using a 2.5 mm hex wrench, remove the fasteners

from the Battery Slides. See

Figure 58

4. Remove the Battery Slides.

Installation

1. Make sure the SE-3 Patroller is powered off,

unplugged, and the parking brake is engaged.

2. Align the Battery Slides in the battery compartment.
3. Using a 2.5 mm hex wrench, install the fasteners.

Torque to

1.0 N-m (0.74 ft-lbf)

4. Install the Battery Module (

page 8

Figure 58: Battery Slides

20709-00001

1.0 N-m (0.74 ft-lbf)

Battery Compartment

Содержание SE-3 Patroller





















































































































































Результаты поиска

Содержание SE-3 Patroller

Отзывы:

Бренды по названию

Популярные бренды

Segway SE-3 Patroller, Руководство по обслуживанию

Результаты поиска

Содержание SE-3 Patroller

Отзывы:

Бренды по названию

Популярные бренды