manualshive.com logo in svg

Segway SE-3 Patroller, Руководство по обслуживанию

Поделиться
Скачать
Segway SE-3 Patroller Скачать руководство пользователя страница 128

SE-3 Patroller

120

Rear Strobe Light Harness

This harness connects the PI Board to the rear strobe lights.

Tools Required:

  Wire cutters

Removal

1.  Make sure the SE-3 Patroller is powered off, 

unplugged, and the parking brake is engaged.

2.  Remove the following components:

a.  Battery Module (

page 8

)

b.  Storage Trays (

page 13

)

c.  Bib Panel (

page 14

)

d.  Glove Box (

page 16

)

e.  Front Cowl (

page 17

)

f.  Light Cluster (

page 18

)

g.  Right Side Panel (

page 20

)

h.  Electronics Shield (

page 100

)

i. 

Rider Detect Mat (

page 82

)

j. 

Motor Cavity Lid (

page 89

)

3.  Disconnect the wire harness from the PI Board. 

See 

Figure 166

.

4.  Remove the two cable ties on the side of the frame.
5.  Using a pair of wire cutters, remove the two cable ties 

at the rear of the Motor Cavity.

6.  Remove the Rear Strobe Light Harness.

Figure 166:  Rear Strobe Light Harness to PI Board

Figure 167:  Rear Strobe Light Harness to Lights

Rear Strobe 

Lights

Harnesses

Содержание SE-3 Patroller





















































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды