Renesas SH7124 R5F7124 Скачать руководство пользователя страница 508 | Manualshive

Страница: 508 / 782

background image

Section 13 A/D Converter (ADC)

Rev. 3.00 Sep. 27, 2007 Page 488 of 758

REJ09B0243-0300

13.4 Operation

The A/D converter operates by successive approximation with 10-bit resolution. It has two
operating modes; single mode and scan mode. There are two kinds of scan mode: continuous
mode and single-cycle mode. When changing the operating mode or analog input channel, in order
to prevent incorrect operation, first clear the ADST bit to 0 in ADCR.

13.4.1 Single

Mode

In single mode, A/D conversion is to be performed only once on the specified single channel. The
operations are as follows.

1. A/D conversion is started when the ADST bit in ADCR is set to 1, according to software,

MTU2, or external trigger input.

2. When A/D conversion is completed, the result is transferred to the A/D data register

corresponding to the channel.

3. On completion of conversion, the ADF bit in ADCSR is set to 1. If the ADIE bit is set to 1 at

this time, an ADI interrupt request is generated.

4. The ADST bit remains set to 1 during A/D conversion. When A/D converion ends, the ADST

bit is automatically cleared to 0 and the A/D converter enters the idle state.
When the ADST bit is cleared to 0 during A/D conversion, A/D conversion stops and the A/D
converter enters the idle state.

13.4.2 Continuous

Scan

Mode

In continuous scan mode, A/D conversion is to be performed sequentially on the specified
channels.

1. When the ADST bit in ADCR is set to 1 by software, MTU2, or external trigger input, A/D

conversion starts on the channel with the lowest number in the group (AN0, AN1, ..., AN3).

2. When A/D conversion for each channel is completed, the result is sequentially transferred to

the A/D data register corresponding to each channel.

3. When conversion of all the selected channels is completed, the ADF bit in ADCSR is set to 1.

If the ADIE bit is set to 1 at this time, an ADI interrupt is requested after A/D conversion ends.
Conversion of the first channel in the group starts again.

4. Steps 2 to 3 are repeated as long as the ADST bit remains set to 1. When the ADST bit is

cleared to 0, A/D conversion stops and the A/D converter enters the idle state.

«
...
506
507
508
509
510
...
»

Содержание SH7124 R5F7124















































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SH7124 R5F7124

Бренд: Samsung Страницы: 2

Бренд: Samsung Страницы: 31

Бренд: Samsung Страницы: 15

Бренд: VAF instruments Страницы: 56

Бренд: Salus Страницы: 16

Бренд: Accuphase Страницы: 2

Бренд: ADTRAN Страницы: 2

AMB-VDX3H1 Series

Бренд: Acrosser Technology Страницы: 4

Бренд: Paradyne Страницы: 1

Бренд: JETWAY Страницы: 55

Procont LMC-008-IO

Бренд: janitza Страницы: 28

SABVISION NVR32

Бренд: SAB Страницы: 29

Бренд: NC-link Страницы: 20

Бренд: Idis Страницы: 22

Бренд: B&B Electronics Страницы: 17

Бренд: Cooler Master Страницы: 4

Бренд: X-Micro Страницы: 24

Бренд: Devolo Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды