Regency Fireplace Products Greenfire GF950L Series Скачать руководство пользователя страница 83 | Manualshive

Страница: 83 / 104

background image

Regency GF950L-2 Gas Fireplace

83

END OF LINE POWER FLUE MAINTENANCE

EXTERNAL POWER FLUE ACCESS

1. Remove 4 screws located around inner trim (Diagram 1).

2. Loosen 4 screws (Diagram 2) and slide shield up and out. Once access has

been made into power flue housing, you can remove the pressure switch
and fan motor.

3. Remove the pressure switch by disconnecting red and green wires from

pressure switch (Diagram 3) Disconnect Hose from underside of pressure
switch (Diagram 4)

4. Loosen (1) one Phillips head screw securing the pressure switch to the power

flue housing (Diagram 5) once the pressure switch is free from the Housing
unit, it is possible to replace the pressure switch by removing (1) one Phillips
head screw holding the pressure switch to mounting bracket (Diagram 6).

Replacing the power flue motor:

1. Turn off power supply.

2. Loosen 6 x 1/4” hex screws slightly.

3. Turn power flue motor counter clockwise and lift out (Diagram 7).

4. Disconnect power to the motor by disconnecting black and black wire and white

and black wire (Diagram 8). The power flue motor is now free from the unit.

5. Loosen 4 screws and slide shield up and out (Diagram 2). Once access to

the power flue housing is achieved, you can remove the pressure switch
and fan motor.

6. Remove the pressure switch by disconnecting the red and green wires from

the pressure switch (Diagram 3)

7. Disconnect the hose from the underside of the pressure switch (Diagram 4).

Loosen one Phillips head screw holding the pressure switch to the power
flue housing (Diagram 5). Once the pressure switch is free from the hous-
ing it is possible to replace the pressure switch by removing one Phillips
head screw holding the pressure switch to mounting bracket. (Diagram 6)

8. To replace the power flue motor, first turn off the power supply, then slightly

loosen 6 x 6.35mm hex screws. Turn the power flue motor counter clockwise
and pull it out (Diagram 7).

9. Disconnect the power to the motor by disconnecting the black and black

from the terminal block. The power flue motor is now free.

Diagram 1

Diagram 2

Diagram 7

Diagram 3

Diagram 4

Diagram 5

Diagram 6

Diagram 8

maintenance

«
...
81
82
83
84
85
...
»

Содержание Greenfire GF950L Series









































































































Отзывы:

Нет отзывов

Похожие инструкции для Greenfire GF950L Series

Бренд: Wamsler Страницы: 82

Бренд: Majestic Страницы: 4

CLEARion Series

Бренд: Napoleon Страницы: 30

Бренд: United States Stove Страницы: 4

Бренд: NovaFlex Страницы: 24

Бренд: Stone Age Страницы: 14

Бренд: Rinnai Страницы: 20

Бренд: Quadra-Fire Страницы: 26

CASUAL FIRESIDE 5110-2872O-E

Бренд: OW Lee Страницы: 28

FireGenie PG121-LPG1

Бренд: Regency Страницы: 44

Бренд: Charlton & Jenrick Страницы: 8

Бренд: Napoleon Страницы: 2

Бренд: Napoleon Страницы: 2

Бренд: Napoleon Страницы: 4

Бренд: Nibe Страницы: 44

Бренд: Outdoor Lifestyles Страницы: 33

Бренд: Hearth and Home Technologies Страницы: 32

Бренд: Hearth and Home Technologies Страницы: 61

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды