Regency Fireplace Products Greenfire GF950L Series Скачать руководство пользователя страница 75

Страница: 75 / 104

Regency GF950L-2 Gas Fireplace

installation

919-220

11/13/15

GF900

GLASS SURROUND INSTALLATION

Install the fascia to the unit by hooking the left and right side mounting brackets into the mounting slots at the side of the fi rebox as shown

below. It is recommended that you use the fi rst mounting slot (the one closest to the door frame overlay) out of the 3 so that the faceplate

and door frame overlay are fl ush with one another. See diagram below.

NOTE: There are 3 mounting slots available, this is to accommodate any fi nishing that protrudes slightly beyond the faceplate.

Warning:

Turn off the unit by way of the wall switch or remote.

Allow unit to cool at least 10 min. - prior to removing the

faceplate.

Diagram 1 - Glass Surround Install

Diagram 3- Final Install

Diagram 2 - adjustments

+1/4" (6mm)

+1/2" (13mm)

Use fi rst notch in bracket

for standard installation

919-615a

05.27.16

GF900/GF1500L

919-615a

05.27.16

OPTIONAL FINISHING TRIM INSTALLATION

tooltip

1. Install the optional finishing trim by lining up trim with the outside of

the fascia. Press trim inward firmly to seat onto the unit.

2. Pull trim outward–away from the unit to remove.

Finishing Trim Installed

OPTIONAL FINISHING TRIM INSTALLATION

tooltip

1. Install the optional finishing trim by lining up trim with the outside of

the fascia. Press trim inward firmly to seat onto the unit.

2. Pull trim outward–away from the unit to remove.

Finishing Trim Installed

GF900/GF1500L

OPTIONAL FINISHING TRIM INSTALLATION

Содержание Greenfire GF950L Series









































































































Результаты поиска

Содержание Greenfire GF950L Series

Отзывы:

Похожие инструкции для Greenfire GF950L Series

Бренды по названию

Популярные бренды

Regency Fireplace Products Greenfire GF950L Series, Инструкция для владельца и по установке

Результаты поиска

Содержание Greenfire GF950L Series

Отзывы:

Похожие инструкции для Greenfire GF950L Series

Бренды по названию

Популярные бренды