Regency Fireplace Products Greenfire GF950L Series Скачать руководство пользователя страница 31

Страница: 31 / 104

Regency GF950L-2 Gas Fireplace

installation

The shaded area in the diagram shows all allowable combinations
of straight vertical and offset to vertical terminations, using two
45

elbow, with

Rigid Pipe Flueing Systems.

• Flue must be supported at offsets.

• Minimum distance between elbows is 305mm.

• Maintain clearances to combustibles as listed in the

"Clearances" section in the manual.

• Horizontal flue must be supported every 1M.

• Refer to the "Flue Restrictor Position" section for

details on how to change the flue restrictor from the
factory setting of Set 0 or Set 3 if required.

• Note: For ULPG Flue Restrictor - Set to "0" - 75mm

open.

FLUEING ARRANGEMENT FOR VERTICAL TERMINATIONS (NON POWER FLUE)
Vertical Flueing with Two (2) 45

Elbows

6.7m

Res

trictor Set #3

18mm open

Metres

VerticalHeight(Metres)

NOTE: FOR ULPG

FLUE RESTRICTOR

SET TO "0" - 75mm OPEN

Содержание Greenfire GF950L Series









































































































Результаты поиска

Содержание Greenfire GF950L Series

Отзывы:

Похожие инструкции для Greenfire GF950L Series

Бренды по названию

Популярные бренды

Regency Fireplace Products Greenfire GF950L Series, Инструкция для владельца и по установке

Результаты поиска

Содержание Greenfire GF950L Series

Отзывы:

Похожие инструкции для Greenfire GF950L Series

Бренды по названию

Популярные бренды