Regency Fireplace Products Greenfire GF950L Series Скачать руководство пользователя страница 55 | Manualshive

Страница: 55 / 104

background image

Regency GF950L-2 Gas Fireplace

55

920-276c

10.29.20

WARNING

This conversion kit shall be installed by a qualified
service agency in accordance with the manufacturer’s
instructions and all applicable codes and require-
ments of the authority having jurisdiction. If these
instructions is not followed exactly, a fire, explosion
or production of carbon monoxide may result causing
property damage, personal injury or loss of life. The
qualified service agency is responsible for the proper
installation of this kit. The installation is not proper
and complete until the operation of the converted ap-
pliance is checked as specified in the manufacturer’s
instructions supplied with the kit.

Conversion Kit includes:

1

911-339

Wiring Harness

1

946-765 or 946-542

Power Flue

1

910-327

Strain Relief

Natural Non Power Flue to Power Flue Conversion follow steps below:

1. Install either Inline/End of line power flue systems first. Refer to the gas

power flue installation instructions based on your type of power flue
system that will be used. Once the flue system has been installed the
wire harness may then be brought to the appliance as per steps below.

2. Run the power flue wire harness from the inline/end of line power flue to

the appliance. Excess wire can be rolled up as shown below and placed
where space is available such as in an attic space, or within a chase.

5. Run the wires into the appliance until the strain relief mounting plate is

reached. Screw the mounting plate onto the appliance using 4 supplied
Phillips head screws.

4. Insert the power flue wire harness through the square opening.

3. Locate the opening on the left hand side of the appliance beside the

power cord.

6. Remove the 4 Phillips head screws on the front panel plate to gain access

to the ECS V control module.

7. Remove the nut on the grounding screw located on the left hand side of

the appliance and connect the additional ground wire from the power flue
wire harness. Reinstall the grounding screw nut.

1

GF950 ECS V

Natural Vent to Power Vent Conversion

WARNING

ELECTRICAL CONNECTIONS SHOULD ONLY BE CARRIED OUT BY A QUALIFIED AND LICENSED ELECTRICIAN

Natural Flue to Power Flue Conversion

NATURAL FLUE TO POWER FLUE CONVERSION

installation

«
...
53
54
55
56
57
...
»

Содержание Greenfire GF950L Series









































































































Отзывы:

Нет отзывов

Похожие инструкции для Greenfire GF950L Series

Бренд: Napoleon Страницы: 2

Бренд: Napoleon Страницы: 84

Бренд: Napoleon Страницы: 16

Бренд: Napoleon Страницы: 4

Бренд: Napoleon Страницы: 56

Бренд: Napoleon Страницы: 36

Бренд: Napoleon Страницы: 24

Бренд: Napoleon Страницы: 48

Бренд: Napoleon Страницы: 2

Бренд: Napoleon Страницы: 52

Бренд: Napoleon Страницы: 40

PATIOFLAME GPFN

Бренд: Napoleon Страницы: 32

Бренд: Napoleon Страницы: 36

Бренд: Paloform Страницы: 14

Бренд: Rinnai Страницы: 21

Home VERSANORA VNF-00115

Бренд: Teamson Страницы: 21

Бренд: Amantii Страницы: 21

Бренд: Zibro Страницы: 103

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды