manualshive.com logo in svg

Regency Fireplace Products Greenfire GF950L Series, Инструкция для владельца и по установке

"Regency Fireplace Products Greenfire GF950L Series представляет собой элегантную и эффективную линейку каминов. Для установки и эксплуатации этого продукта необходимо скачать бесплатное руководство владельца и инструкцию по установке с веб-сайта manualshive.com. Получите актуальные сведения о продукте, скачав руководство прямо сейчас."

Поделиться
Скачать
background image

Regency GF950L-2 Gas Fireplace

3

table of contents

Copy of Data Badge ......................................................5
Unit Dimensions ............................................................6

Installation ....................................................................7

Important Message   ......................................................7
General Safety Information ............................................7
Installation Checklist ......................................................8
Locating Your Gas Fireplace ..........................................8
Clearances ....................................................................9
Framing Dimensions ....................................................10
Combustible Finishing
Unit Assembly/ Finishing/ Mantel Clea Mantel Leg 
Clearances ..................................................................11
Installation Access Panel .............................................11
Framing & Finishing (Combustible)..............................12
Combustible Requirements .........................................12
Clearances for Combustible Finishing with Mantel ......13
Combustible Mantel Leg Clearances ...........................13
Non-Combustible Flushed Finishing

Unit Assembly/ Finishing/ Mantel Clearances 
+ Mantel Leg Clearances .....................................14
Remove Top Nailing Strips & Standoffs ...............14
Installation Access Panel .....................................14

Clearances for Non-Combustible Flushed Finishing with 
Mantel ..........................................................................15
Non-Combustible Mantel Leg Clearances ...................15
Flushed Finishing & Framing with Non-Combustible  
Material ........................................................................16
Non-Combustible Requirements..................................16
Installing a TV / Artwork Flush with the Unit ................17
Installing a TV / Artwork Enclosed above the Unit .......18
Optional Framing Kit ....................................................19
Non-Combustible Facing Installation ...........................20
Framing & Finishing (Clean Finish Installations Only) .21
Flue Restrictor Position ...............................................22
Natural Flue ...........................................................23-36
Exterior Flue Termination Locations ............................23
Clearances ..................................................................24
102mmx168mm Rigid Pipe Cross Reference Chart 25-26
Flueing Introduction (Non Power Flue) ........................27
Flueing Arrangement for Horizontal Terminations .......27
Flueing Arrangements - Horizontal Termination (Flex) 28
Horizontal Terminations-Rigid Pipe 102mmx168mm 29-30
Flueing Arrangement for Vertical Terminations
  -Vertical Flueing with Two Elbows ..............................31
Direct Flue Wero Clearance Top Exit Vertical Flue Kit .32
Vertical Termination - Vertical Flex Flue Kit .................33
Vertical Flue Extension Kit ...........................................34
Ceiling Firestop / Firestop Spacer ...............................34
Vertical terminations - Rigid Pipe 102mm x 168mm ....35
Wiring Diagram - Non Power Flue ...............................36
Inline Power Flue ..................................................37-57
Exterior Flue Termination Locations ............................37
Clearances ..................................................................38
Flueing Introduction .....................................................39

Flue Arrangements for Horizontal Terminations
  -Inline Horizontal Flue Chart ......................................39
Flue Restrictor Position ...............................................39
Horizontal Terminations - Inline Power Flue
  102mm x 168mm Flex Flue .......................................40
Unit Installation with Horizontal Termination 102 mm x 
168 mm Flueing (Flex Flue Systems) ..........................41
AstroCap Dimensions ..................................................41
Horizontal Terminations - Inline Power Flue
Rigid Pipe 102 mm x 168 mm .....................................42
Unit Installation with Horizontal Termination 102 mm x 
168 mm Flueing (Rigid Flue Systems) ........................43
Flueing Arrangement for Vertical Terminations - Inline
Power Flue ...................................................................44
Vertical Inline Power Flue Terminations - Flex Pipe 45-46
Vertical Flue Extension Kit-Horizontal Power Flue Kit .47
Ceiling Firestop / Firestop Spacer ...............................47
Vertical Inline Power Flue Terminations - Rigid Pipe ...48
Bypass Adjustment ......................................................50
Inline Power Flue Dimensions .....................................51
Gas Power Flue Installation - Framing
Inline Power Flue Terminations ....................................52
Power Flue Terminal Installation - Inline Power Flue 
Terminations ................................................................53
Gas Power Flue Installation Clearance Requirements
Inline Power Flue Terminations ....................................54
Natural Flue to Power Flue Conversion .......................55
Wiring Diagram - Power Flue .......................................57
End of Line Power Flue ........................................58-76
Exterior Flue Termination Locations ............................58
Clearances ..................................................................59
Flueing Introduction .....................................................60
Flueing Arrangements for Horizontal Terminations -
End of Line Horizontal Power Flue Chart ....................60
Flue Restrictor Position ...............................................60
Unit Installation with Horizontal Terminations - End of 
Line Power Flue 102 mm x 168 mm Flex Flueing ........61
Horizontal Terminations - End of Line Power Flue
Rigid Pipe 102 mm x 168 mm .....................................62
Unit Installation with Horizontal Terminations - End of 
Line Power Flue 102 mm x 168 mm Rigid Flueing ......63
Gas Power Flue Installation - Wiring -
End of Line Power Flue ...............................................64
System Data ................................................................65
High Elevation ..............................................................65
Gas Line Installation ....................................................65
Pilot Adjustment ...........................................................65
Gas Pipe Pressure Testing ..........................................65
845 S.I.T. Valve Description .........................................66
Aeration Adjustment ....................................................66
Optional Fan Ducting Kit Installation ............................67
Optional Fan Kit Installation .........................................68
Fan Duct Extension Kit Installation ..............................69
Wiring Diagram ............................................................69
Log Set Installation ......................................................70
Front Trim Removal / Installation .................................72

Содержание Greenfire GF950L Series









































































































Отзывы:

Нет отзывов

Похожие инструкции для Greenfire GF950L Series

Valor Heartbeat OXYSAFE 2 Owner'S Manual preview
Heartbeat OXYSAFE 2
Бренд: Valor Страницы: 10
Majestic 400DVBLN/PV7 Installation And Operating Instructions Manual preview
400DVBLN/PV7
Бренд: Majestic Страницы: 60
Vermont Castings 647 BFC Installation And Operating Manual preview
647 BFC
Бренд: Vermont Castings Страницы: 24
Desa W23FT Assembly And Installation Instructions preview
W23FT
Бренд: Desa Страницы: 4
UNIPRODO UNI G CHIMNEY 06 User Manual preview
UNI G CHIMNEY 06
Бренд: UNIPRODO Страницы: 11
Vanguard BHDV34PB Owner'S Operation And Installation Manual preview
BHDV34PB
Бренд: Vanguard Страницы: 38
Valor H4 650JN Installation Manual preview
H4 650JN
Бренд: Valor Страницы: 54
Desa EL36L Safety Information And Installation Manual preview
EL36L
Бренд: Desa Страницы: 20
Saey Fenix 80 FL Installation And User Manual preview
Fenix 80 FL
Бренд: Saey Страницы: 44
HAMPTON BAY AD1585H Use And Care Manual preview
AD1585H
Бренд: HAMPTON BAY Страницы: 7
barbas UNILUX-6 55 Instructions For Use & Maintenance Manual preview
UNILUX-6 55
Бренд: barbas Страницы: 32
Camina & Schmid Lina 4545 s Operating Instructions Manual preview
Lina 4545 s
Бренд: Camina & Schmid Страницы: 40
Country Hearth 2200IE Owner'S Operation And Instruction Manual preview
2200IE
Бренд: Country Hearth Страницы: 20
Chinook Fireplaces BWI-30A Homeowner And Installation Manual preview
BWI-30A
Бренд: Chinook Fireplaces Страницы: 16
OW Lee CASUAL FIRESIDE 5110-2875O Manual preview
CASUAL FIRESIDE 5110-2875O
Бренд: OW Lee Страницы: 28
OW Lee CASUAL FIRESIDE 5110-2442O-E Manual preview
CASUAL FIRESIDE 5110-2442O-E
Бренд: OW Lee Страницы: 28
OW Lee 5114-42BTC Manual preview
5114-42BTC
Бренд: OW Lee Страницы: 28
Heat Surge Accent Manual preview
Accent
Бренд: Heat Surge Страницы: 36

Бренды по названию

Популярные бренды

Загрузить еще бренды