Regency Fireplace Products Greenfire GF950L Series Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 104

background image

Regency GF950L-2 Gas Fireplace

11

Nailing Strips

(DO NOT REMOVE NAILING STRIPS

WHEN USING COMBUSTIBLE FINISHING)

installation

UNIT ASSEMBLY PRIOR TO INSTALLATION

The nailing strips must be correctly positioned and attached before
unit is slid into position.

NAILING STRIPS-COMBUSTIBLE FINISHING

The nailing strips come attached to the unit. There is 1 plate on each side,
1 on the top.
The top and side nailing strips are secured to the framing.

Note: The rear & side standoffs are shipped in a flat position. These must be
bent into a V shape and secured to the appliance with the screws supplied.

IMPORTANT NOTE

Framing depth measurement is noted with the nailing strips
set as far forward on the firebox as possible. The nailing
strips can be adjusted back up to 38mm to allow for varying
thicknesses in non-combustible material & wall finishes.

INSTALLATION ACCESS PANEL

The unit is equipped with a removable access panel for pre-finish installation
of optional components—this panel is located on the lower front face.

1. Remove 4 screws to remove access panel.

2. Easier access to gas connection with panel removed.

3. Install any optional components with access panel removed.

4. Reinstall access panel, line up 2 upper tabs and secure in place with

4 screws.

Note: Access panel is no longer usable/accessible once facing material

installed.

Installation Access Panel

Tab locations on access panel

COMBUSTIBLE FINISHING
UNIT ASSEMBLY/ FINISHING/ MANTEL CLEA MANTEL LEG CLEARANCES

«
...
9
10
11
12
13
...
»

Содержание Greenfire GF950L Series









































































































Отзывы:

Нет отзывов

Похожие инструкции для Greenfire GF950L Series

Бренд: Panadero Страницы: 36

Бренд: Remii Страницы: 26

Бренд: Rinnai Страницы: 21

e-MatriX 800-500 ST LL

Бренд: Faber Страницы: 24

Бренд: Gasmate Страницы: 12

Бренд: Cal Flame Страницы: 32

Бренд: Ravelli Страницы: 9

Бренд: EdilKamin Страницы: 26

Бренд: ORTAL Страницы: 39

Tahoe DVP36PP32EN-1

Бренд: Empire Comfort Systems Страницы: 64

Бренд: Jocel Страницы: 22

Бренд: Travis Industries Страницы: 64

Бренд: Whalen Страницы: 60

Бренд: BLUE SKY Страницы: 8

Бренд: BLUE SKY Страницы: 14

Бренд: The Fireplace Страницы: 8

5700 STEP TOP ACC

Бренд: Quadra-Fire Страницы: 28

Бренд: Paragon Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды