Regency Fireplace Products Greenfire GF950L Series Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 104

background image

60

Regency GF950L-2 Gas Fireplace

Power Flue Aeration:
NG: 4.4 mm
Propane: 11 mm
ULPG: 13 mm

NOTE: Ensure aeration is set to correct configuration.

installation

FLUEING INTRODUCTION (END OF LINE POWER FLUE)

The GF950L uses the "balanced flue" technology Co-Axial system. The inner liner flues products of combustion to the outside while the outer liner draws outside
combustion air into the combustion chamber thereby eliminating the need to use heated room air for combustion and losing warm room air up the chimney.

Note: These flue pipes must not be connected to any other appliance.

The gas appliance and flue system must be vented directly to the outside of the building, and never be attached to a chimney serving a separate solid fuel or
gas burning appliance. Each direct vent gas appliance must use it's own separate flue system. Common flue systems are prohibited.

The gas power flue system is designed to allow the installation of a gas appliance when typical natural flue configurations are not possible. Must be
terminated horizontally. Vertical terminations are not permitted.

Important:
Maximum total flue length = 18m maximum of six - 90° elbows permitted.
One 90° elbow = two 45° elbows.
Maximum total negative flue length = 2m.
Minimum (1.22 m) from the unit prior to terminating.

Note: Maximum length of 18m is based on overall length of combined
chimney components.

Do not run positive flueing after a negative run.

FLUEING ARRANGEMENTS FOR HORIZONTAL TERMINATIONS
END OF LINE HORIZONTAL POWER FLUE FLUE CHART

Note: Rigid pipe is approved for up to 18m.
Note: Flex pipe is approved for up to 12m using 2 X 946-756 - 6m flex kits.

FLUE RESTRICTOR POSITION

This negative run is for the end of
line power flue cap only. Do not run
with the inline power flue.

18m Overall length Max.

Shown with 5 - 90

0

elbows

Restrictor - Set 3 - 18mm open

18m Overall length Max.

Shown with 3 - 90

0

elbows

18m Run (no rise)

Shown with 2 elbows (Negative run 18m)

«
...
58
59
60
61
62
...
»

Содержание Greenfire GF950L Series









































































































Отзывы:

Нет отзывов

Похожие инструкции для Greenfire GF950L Series

Бренд: Valcourt Страницы: 95

Madrona MF28JLN NG

Бренд: Valor Страницы: 42

Бренд: Uniflame Страницы: 8

Бренд: Gasmate Страницы: 12

Бренд: Mendota Страницы: 45

PONDEROSA LS-24P-1

Бренд: White Mountain Hearth Страницы: 12

Бренд: Vermont Castings Страницы: 14

Бренд: Landmann Страницы: 6

Бренд: Valor Страницы: 28

CASUAL FIRESIDE 5110-30RDC

Бренд: OW Lee Страницы: 28

Бренд: UKIAH Страницы: 24

Бренд: Lennox Hearth Products Страницы: 16

Fiery Rock OFG147NG

Бренд: ELEMENTI Страницы: 20

astria Mission Mission36TMN

Бренд: IHP Страницы: 32

Бренд: Harrie Leenders Страницы: 16

Бренд: Jensen Страницы: 54

Бренд: Tulikivi Страницы: 2

Бренд: Tulikivi Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды