Regency Fireplace Products Greenfire GF950L Series Скачать руководство пользователя страница 50 | Manualshive

Страница: 50 / 104

background image

50

Regency GF950L-2 Gas Fireplace

920-235

03.24.20

1

GF950PV

IMPORTANT: Adjust the bypass plate before installing the inline power flue. Refer to the flueing section for your unit’s bypass setting. Once the inline
power flue is installed and the flueing is connected, the bottom access panel to the bypass plate may not be accessible for further adjustment.
A bypass plate is used to adjust the flowrate of the exhaust being pulled from the unit. To adjust the bypass plate:

Bypass Adjustment

1.

Remove the four screws on the bottom access panel.

2.

Remove the two screws on the bypass plate and slide the plate to the

appropriate setting (refer to unit's flue chart).

3.

Reinstall the bypass plate screws.

3.

Reinstall bottom access panel screws.

BYPASS ADJUSTMENT (INLINE POWER FLUE)

installation

«
...
48
49
50
51
52
...
»

Содержание Greenfire GF950L Series









































































































Отзывы:

Нет отзывов

Похожие инструкции для Greenfire GF950L Series

Valencia VWWF-1/0306

Бренд: Warm House Страницы: 35

Бренд: Napoleon Страницы: 60

Бренд: Restoration Hardware Страницы: 4

Elevation EX36NTEL

Бренд: Napoleon Страницы: 128

Бренд: barbas Страницы: 32

Бренд: Majestic Страницы: 20

Flush Wood Plus

Бренд: Travis Industries Страницы: 32

Бренд: BOND MANUFACTURING Страницы: 22

Бренд: EcoSmart Fire Страницы: 12

Бренд: Robinson Willey Страницы: 27

Бренд: Focal Point Страницы: 17

Бренд: Nordpeis Страницы: 72

Бренд: Coleman Страницы: 8

Бренд: Heat&Glo Страницы: 9

Бренд: Heat&Glo Страницы: 36

Бренд: Masport Страницы: 20

Intrepid II 1308

Бренд: Vermont Castings Страницы: 29

WHEATON 1007519970/320010627/611768149018/23WM90536-PC78

Бренд: StyleWell Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды