Regency Fireplace Products Greenfire GF950L Series Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 104

background image

Regency GF950L-2 Gas Fireplace

15

CLEARANCES FOR NON-COMBUSTIBLE FLUSHED FINISHING WITH MANTEL

Due to the extreme heat this fireplace emits, the mantel
clearances are critical.

Combustible mantel clearances from top of front facing are shown
in the diagram on the right.

Note: For a flushed finish using non-combustible finishing, seven
13mm stand-off tabs around the fireplace opening must be broken
off. The top nailing flange cannot be used and a non-combustible
steel stud must be installed to support the non-combustible facing.

Note: Ensure the paint that is used on the mantel and the

facing is "high quality" or the paint may discolour.

Note: Combustible mantel starts at 796mm (605mm + 191mm)

from unit base.

NON-COMBUSTIBLE MANTEL LEG CLEARANCES

Mantel leg & Non-combustible finishing clearances as per diagram: (Flushed Finish)

Allowablemantel

leg projection

181mm

254mm

330mm

38mm

MANTELLEG

102mm

178mm

Allowablemantel

leg projection

181mm

254mm

330mm

38mm

MANTELLEG

102mm

178mm

Allowablemantel

leg projection

181mm

254mm

330mm

38mm

MANTELLEG

102mm

178mm

83mm

Non-combustible

83mm

Non-combustible

Combustible Material

(152mm)

(305mm)

(0mm)

To Uni

t

Base

(605mm)

(254mm)

Top of

Fireplace

Opening

(508mm)

(305mm)

(420mm)

(191mm)

Non-Combustible facing (min.12mm)

Non-Combustible steel stud

(152mm)

756mm to underside

of steel stud

(100mm)

(247mm)

(200mm)

(322mm)

installation

«
...
13
14
15
16
17
...
»

Содержание Greenfire GF950L Series









































































































Отзывы:

Нет отзывов

Похожие инструкции для Greenfire GF950L Series

Бренд: CACHFIRES Страницы: 11

Бренд: Valcourt Страницы: 32

Бренд: Uniflame Страницы: 8

Бренд: Majestic Страницы: 20

Бренд: Piazzetta Страницы: 54

Бренд: Empire Страницы: 44

Бренд: Jeco Страницы: 4

Бренд: Vermont Castings Страницы: 64

Бренд: Amantii Страницы: 36

Linear Pebble FRDPU0MN

Бренд: Flavel Страницы: 9

Zermatt 10033051

Бренд: Klarstein Страницы: 44

Бренд: BECAFIRE Страницы: 67

Бренд: Valcourt Страницы: 6

Jensen Geneva 1581LP

Бренд: KSP Страницы: 51

Бренд: Desa Страницы: 36

Бренд: Oblica Страницы: 10

Бренд: barbas Страницы: 100

Бренд: Sylvania Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды