Napoleon Madison GD80NT Скачать руководство пользователя страница 1

Страница: 1 / 56

W415-0695 / A / 06.07.10

$10.00

INSTALLER: LEAVE THIS MANUAL WITH THE APPLIANCE.

CONSUMER: RETAIN THIS MANUAL FOR FUTURE REFERENCE.

INSTALLATION AND

OPERATING INSTRUCTIONS

1.2A

Wolf Steel Ltd., 24 Napoleon Rd., Barrie, ON, L4M 4Y8 Canada /

103 Miller Drive, Crittenden, Kentucky, USA, 41030

Phone (705)721-1212 • Fax (705)722-6031 • www.napoleon

replaces.com • [email protected]

SAFETY INFORMATION

WARNING

If the information in these instructions are
not followed exactly, a fi re or explosion
may result causing property damage,
personal injury or loss of life.

- Do not store or use gasoline or other fl ammable
vapors and liquids in the vicinity of this or any
other appliance.

- WHAT TO DO IF YOU SMELL GAS:
•

Do not try to light any appliance.

•

Do not touch any electrical switch; do not use
any phone in your building.

•

Immediately call your gas supplier from a
neighbour’s phone. Follow the gas supplier’s
instructions.

•

If you cannot reach your gas supplier, call the
fi re department.

- Installation and service must be performed by a
qualifi ed installer, service agency or the supplier.

CERTIFIED FOR CANADA AND UNITED STATES USING ANSI/CSA METHODS.

GD80NT

NATURAL GAS

GD80PT

PROPANE

CERTIFIED UNDER CANADIAN AND AMERICAN NATIONAL STANDARDS: CSA 2.33, ANSI Z21.88 FOR VENTED GAS FIREPLACE HEATERS.

Содержание Madison GD80NT

























































Результаты поиска

Содержание Madison GD80NT

Отзывы:

Похожие инструкции для Madison GD80NT

Бренды по названию

Популярные бренды

Napoleon Madison GD80NT, Инструкция по установке и эксплуатации

Результаты поиска

Содержание Madison GD80NT

Отзывы:

Похожие инструкции для Madison GD80NT

Бренды по названию

Популярные бренды