Racal Instruments 1256E Скачать руководство пользователя страница 88 | Manualshive

Страница: 88 / 204

background image

1256E User Manual

Computer Interfaces 4-24

Racal Instruments

©

2002

(sum of all bits including parity bit is an even number or zero),
and “odd” (sum of all bits including parity is an odd number).
For most applications, this is set to “none”.

To set these parameters, proceed as follows:

1. Press the top key. Rotate the knob until the top line reads:

>-----SETTINGS-----<

2. Select line 2 (next to top line) by pressing the second key. This

selects line 2 so that you may select the type of setting to work
with:

-----SETTINGS-----
> Type: Display <
Option: Format
Status: Decimal

3. Rotate the knob until line 2 reads as shown below (lines 3 and

4 may differ):

-----SETTINGS-----
> Type: RS-232 <
Option: Data Bits
Status: 8

4. Press the third key to select line 3 of the display. Rotate the

knob until line 3 indicates the desired parameter as shown
below (in this example, the parity option is chosen):

-----SETTINGS-----
Type: RS-232
> Option: Parity <
Status: Even

5. If line 4 of the display already indicates the desired choice for

the parameter, then no action is necessary. Otherwise, press
the fourth key. Rotate the knob until line 4 displays the desired
choice (in this example, “None” is the desired choice):

-----SETTINGS-----
Type: RS-232
Option: Parity
<Update?: None

Then press the fourth key to confirm the update. Pressing
any other button cancels the change.

Set the data terminal or computer to match the settings you select
for the 1256.

«
...
86
87
88
89
90
...
»

Содержание 1256E













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1256E

Бренд: ABB Страницы: 32

Бренд: ABB Страницы: 44

Бренд: ABB Страницы: 15

Бренд: Dataprobe Страницы: 3

Бренд: Panasonic Страницы: 206

Бренд: N-Tron Страницы: 158

Бренд: Cabletron Systems Страницы: 170

Бренд: ATEN Страницы: 2

Бренд: Pulse-Eight Страницы: 9

Бренд: Lionel Страницы: 8

Бренд: Little Giant Страницы: 8

Бренд: Zektor Страницы: 30

Бренд: Belkin Страницы: 288

Бренд: Digital Equipment Страницы: 2

Peripheral Sharer 2 to 1

Бренд: Black Box Страницы: 35

Бренд: Comprehensive Страницы: 6

Бренд: Clever Little Box Страницы: 12

Бренд: PS Automation Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды