Racal Instruments 1256E Скачать руководство пользователя | Manualshive

Страница: 86 / 204

background image

1256E User Manual

Computer Interfaces 4-22

Racal Instruments

©

2002

NOTE

Menu preferences are not normally retained after the
power is removed from the instrument. To make (a)
menu preference(s) permanent, make the desired
change(s) to settings first and then proceed to the
section Storing the Menu Preferences to make the
changes permanent. Following this procedure will put
the settings into non-volatile memory and allow them
to be restored during instrument power-up.

Setting the Message
Termination
Characters

Each message to or from the 1256 must end with an end-of-line
(EOL) character known as a terminator. You may select the EOL
terminator to be any one of the following:

•

Carriage return (CR) only

•

Line feed (LF) only (for non-terminal-based applications, such

as controlling via LabVIEW programs)

•

Carriage return and line feed (CR-LF)

The factory default is line feed only.

To select the EOL terminator, proceed as follows:

1. Press the top key. Rotate the knob until the top line reads:

>-----SETTINGS-----<

2. Select line 2 (next to top line) by pressing the second key. This

selects line 2 so that you may choose the type of setting to
work with:

-----SETTINGS-----
> Type: Display <
Option: Format
Status: Decimal

3. Rotate the knob until line 2 reads as shown below (lines 3 and

4 may differ):

-----SETTINGS-----
> Type: RS-232 <
Option: Data Bits
Status: 8

4. Press the third key to select line 3 of the display. Rotate the

knob until line 3 appears as shown below:

-----SETTINGS-----
Type: RS-232
> Option: EOL Mode <

«
...
84
85
86
87
88
...
»

Содержание 1256E













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1256E

Бренд: GAIM Страницы: 2

Бренд: D-Link Страницы: 267

Бренд: H3C Страницы: 1089

Бренд: Daxten Страницы: 7

COOPER POWER SERIES

Бренд: Eaton Страницы: 16

ATLONA Omega AT-OME-MS52W

Бренд: Panduit Страницы: 123

Atlona AT-OME-MS42

Бренд: Panduit Страницы: 86

Бренд: Aastra Страницы: 52

Бренд: FS Страницы: 41

Бренд: HIKVISION Страницы: 5

UltraHD Switch 3:1

Бренд: Oehlbach Страницы: 20

Бренд: Vega Страницы: 36

Бренд: CableTronix Страницы: 4

Бренд: Eaton Страницы: 5

Бренд: Intel Страницы: 162

Бренд: Microsonic Страницы: 2

Бренд: C&H Technologies Страницы: 28

Бренд: MicroNet Страницы: 123

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды