Racal Instruments 1256E Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 204

background image

1256E User Manual

Using the Front-Panel Controls 3-24

Racal Instruments

©

2002

Enabling or Disabling the Screen Saver

The purpose of the screen saver is to maximize the life of the
fluorescent display. The screen saver automatically turns the
display off after no controls have been operated for a certain time
interval. To set this time interval, refer to

Setting the Screen

Saver Timeout

, later in this section.

To enable or disable the screen saver, proceed as follows:

1. Press the top key next to the display. Rotate the knob until

the top line reads:

>-----SETTINGS-----<

2. Select line 2 (next to the top line) by pressing the second

key. Rotate the knob until line 2 of the display reads
“

Type:Display

“:

-----SETTINGS-----

> Type: Display <
Option: Format
Status: Hex

3. Press the third key to select line 3 of the display (option):

Rotate the knob until line 3 of the display reads as follows:

-----SETTINGS-----
Type: Display
> Option: Saver <
Status: Enabled

4. If line 4 already shows the desired status, then no further

action is necessary. Otherwise, select line 4. Then rotate the
knob until line 4 shows the desired status (enabled or
disabled). This example uses “Disabled”:

-----SETTINGS-----
Type: Display
Option: Saver
<Update?: Disabled

Then press the fourth key (bottom) to update. Pressing any
other key cancels the change.

NOTE

Menu preferences are not normally retained after the
power is removed from the instrument. To make (a)
menu preference(s) permanent, make the desired
change(s) to settings first and then proceed to the
section Storing the Menu Preferences to make the
changes permanent. Following this procedure will put
the settings into non-volatile memory and allow them
to be restored during instrument power-up.

«
...
52
53
54
55
56
...
»

Содержание 1256E













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1256E

OfficeConnect 5

Бренд: 3Com Страницы: 2

OfficeConnect 3C1670500C

Бренд: 3Com Страницы: 18

Бренд: Manhattan Страницы: 2

Бренд: ATZ Страницы: 8

EXT-DVIKVM-441DL

Бренд: Gefen Страницы: 32

Premasreg 716 Series

Бренд: S+S Regeltechnik Страницы: 32

Бренд: Ruby Tech Страницы: 301

Бренд: Contec Страницы: 38

Бренд: ICCN Страницы: 48

Бренд: CYP Страницы: 20

Gigabit Switch 8

Бренд: 3Com Страницы: 2

Бренд: Shadow Страницы: 4

IES6300PRO Series

Бренд: 3onedata Страницы: 5

Бренд: Scion-Tech Страницы: 9

Бренд: Tekvox Страницы: 40

Бренд: Gefen Страницы: 31

Бренд: Abtus Страницы: 2

Бренд: TP-Link Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды