Racal Instruments 1256E Скачать руководство пользователя страница 40

Страница: 40 / 204

1256E User Manual

Using the Front-Panel Controls 3-10

Racal Instruments

2002

To open a relay, follow the steps given in the above section,

Closing a Relay

, except in step 6 rotate the knob until line 4

(bottom line) of the display reads as shown below:

----OPERATIONS----
Slot 03: 1260-118
Channel: 4
<Set to?: Open

Then press the fourth key to open the relay.

Viewing Relay States

It is easy to view the states of the relay channels on a switch
plug-in by using the OPERATIONS menu:

1. Press the top key next to the display. Rotate the knob until

the top line reads:

>----OPERATIONS----<

2. Select line 2 (next to the top line) by pressing the second

key. This selects line 2:

----OPERATIONS----
>Slot 01: 1260-121A<
Channel: 0
Status: Open

3. Rotate the knob until line 2 shows the slot number of the

plug-in you wish to view. This example uses slot 3:

----OPERATIONS----
>Slot 03: 1260-118 <
Channel: 0
Status: Open

4. Press the third key to select line 3 of the display (channel

number). Line 4 of the display shows the state of the
channel 0 relay.

----OPERATIONS----
Slot 01: 1260-118
>Channel: 0 <
Status: Open

5. Rotate the knob one “click” to the right to view the state of

the next relay channel (channel 1):

----OPERATIONS----
Slot 01: 1260-118
>Channel: 1 <
Status: Closed

Rotate the knob right or left to scan through the channels as
desired.

Controlling a Digital Output Port

Содержание 1256E













































































































































































































Результаты поиска

Содержание 1256E

Отзывы:

Бренды по названию

Популярные бренды

Racal Instruments 1256E, Руководство пользователя

Результаты поиска

Содержание 1256E

Отзывы:

Бренды по названию

Популярные бренды