Racal Instruments 1256E Скачать руководство пользователя | Manualshive

Страница: 44 / 204

background image

1256E User Manual

Using the Front-Panel Controls 3-14

Racal Instruments

©

2002

Slot 03: -114TTL
>Port 04: Enable <
Status: Disabled

Now line 4 shows the enable status of the eight-bit buffer for
port 5 (Enabled or Disabled). In this case, it is disabled.

6.

Press the bottom key to select the bottom line of the display.
Then rotate the knob until the display reads as follows:

----OPERATIONS----
Slot 03: -114TTL
>Port 04: Enable <
<Set to?: Enabled

7.

Press the bottom key to complete the operation.

Path Control Menu

Description

The Path Control Menu automatically retrieves pathnames stored
in non-volatile memory at startup and provides the user with
direct control of pathnames from the 1256 front-panel display. It
allows the following operations:

•

View the states of pathnames (closed or open) in the
system.

•

Set pathname filter masks to wildcards or to specific
characters to limit the display of pathnames to those meeting
particular user-criteria.

Defining a Path

The 1256 front-panel enables the user to manually close or open
pathnames after they have been defined remotely using the SCPI
path definition command through one of the remote interfaces.
Refer to “

Naming a Path

” section in Chapter 5 for more details on

defining path names.

Once a path is defined through a remote interface, it is immediately
available for display and use on the front-panel and will remain
visible until either 1) the power is removed from the system or 2)
the path is removed remotely using the SCPI path delete
command. If the intent is to define the pathnames once and make
them accessible to the front panel after power is cycled to the
1256, the defined pathnames must also be stored in non-volatile
memory. Refer to “

Storing Path Names in Non-Volatile

Memory

” section in Chapter 5 for more details.

It is important to realize that the SCPI command language allows
pathname lengths that exceed the display capability of the 1256

«
...
42
43
44
45
46
...
»

Содержание 1256E













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1256E

Бренд: D-Link Страницы: 2

Бренд: D-Link Страницы: 2

DKVM-16 - KVM Switch

Бренд: D-Link Страницы: 24

Dis-200G Series

Бренд: D-Link Страницы: 161

Dis-200G Series

Бренд: D-Link Страницы: 16

Dis-200G Series

Бренд: D-Link Страницы: 47

Бренд: D-Link Страницы: 25

DGS-3100 SERIES

Бренд: D-Link Страницы: 54

DGS-3100 SERIES

Бренд: D-Link Страницы: 220

Бренд: D-Link Страницы: 24

DGS-1248T - Switch

Бренд: D-Link Страницы: 52

DGS-1216T - Switch

Бренд: D-Link Страницы: 42

DGS-1216T - Switch

Бренд: D-Link Страницы: 10

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 379

Бренд: D-Link Страницы: 240

Бренд: D-Link Страницы: 188

DES-3326S - Switch - Stackable

Бренд: D-Link Страницы: 349

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды