Racal Instruments 1256E Скачать руководство пользователя | Manualshive

Страница: 73 / 204

background image

1256E User Manual

Racal Instruments

©

2002

Computer Interfaces 4-9

Setting the Gateway

Setting the gateway is similar to setting the IP address. The
gateway is made up of four octets. Set the gateway by entering the
four octets, one at a time.

1. Press key 3 to select line 3. Rotate the knob until line 3

appears as follows (line 4 may differ):

-----SETTINGS-----
Type: TCP/IP
> Option: GW_Oct_1 <
Status: 0

This prepares the 1256 to set the first octet
(eight bits) of the gateway.

2. Select line 4 and rotate the knob until line 4 displays the first

octet of your desired gateway. Then press key 4 again to
confirm.

3. Proceed with the remaining octets of the gateway until all four

are set.

Setting the Sub-Net Mask

The subnet mask, in like manner as the IP address and gateway,
is comprised of four octets. Set the gateway by entering the four
octets, one at a time.

1. Press key 3 to select line 3. Rotate the knob until line 3

appears as follows (line 4 may differ):

-----SETTINGS-----
Type: TCP/IP
> Option: NM_Oct_1 <
Status: 0

This prepares the 1256 to set the first octet
(eight bits) of the sub-net mask.

2. Select line 4 and rotate the knob until line 4 displays the first

octet of your desired sub-net mask. Then press key 4 again to
confirm.

3. Proceed with the remaining octets of the sub-net mask until all

four are set.

Re-enabling TCP/IP Communications

After setting the address, gateway, and net mask, you must re-
enable TCP/IP communications before the 1256 can use the
Ethernet interface:

1. Ensure that the display shows the “SETTINGS\Remote:

«
...
71
72
73
74
75
...
»

Содержание 1256E













































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 1256E

Бренд: Daxten Страницы: 2

Бренд: Magnetrol Страницы: 12

Бренд: Magnimage Страницы: 53

ATLONA Omega AT-OME-MS52W

Бренд: Panduit Страницы: 123

Atlona AT-OME-MS42

Бренд: Panduit Страницы: 86

Бренд: Xantech Страницы: 2

Бренд: UfiSpace Страницы: 25

Бренд: Equip Страницы: 10

Raritan Dominion LX II

Бренд: LEGRAND Страницы: 7

Бренд: TRENDnet Страницы: 12

Бренд: N-Tron Страницы: 158

Бренд: Electroswitch Страницы: 6

Бренд: Sunix Страницы: 55

CEFLA PIR DALIP

Бренд: DANLERS Страницы: 2

Бренд: Cypress Страницы: 16

Бренд: TRENDnet Страницы: 2

EG2-1600 Series

Бренд: Leonton Страницы: 19

Бренд: LevelOne Страницы: 76

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды