Racal Instruments 1256E Скачать руководство пользователя страница 75

Страница: 75 / 204

1256E User Manual

Racal Instruments

2002

Computer Interfaces 4-11

•

GPIB Cable, 1 meter (3.28 ft.)

P/N 500310-001

•

GPIB Cable, 2 meters (6.56 ft.)

P/N 500310-002

To use the IEEE-488 (GPIB) interface with the 1256 Switching
System, you also need a computer equipped with a GPIB
controller.

GPIB Cabling
Guidelines

Adhere to the following guidelines to maximize the data transfer
rate of the GPIB system:

•

Total cable length of no more than 20 meters (65.6 feet).

•

Maximum separation of 4m (13.2 feet) between devices.

Average separation of no more than 2 meters (6.6 feet).

•

Maximum of 15 devices (including controller) connected to the

bus.

Connecting the
GPIB Cables

Use a GPIB cable to connect the rear-panel GPIB connector on the
1256 to the GPIB port of the host computer. Refer to

Figure 4-2,

Connecting the GPIB Interface

CAUTION

Avoid stacking more than three cables on any single
connector. If the stack is too large, side forces may
damage the connector mounting.

CAUTION

Tighten the locking screws finger-tight on each
connector. Do not over-tighten.

Содержание 1256E













































































































































































































Результаты поиска

Содержание 1256E

Отзывы:

Похожие инструкции для 1256E

Бренды по названию

Популярные бренды

Racal Instruments 1256E, Руководство пользователя

Результаты поиска

Содержание 1256E

Отзывы:

Похожие инструкции для 1256E

Бренды по названию

Популярные бренды