Quantum SNC 4000 Скачать руководство пользователя страница 96

Страница: 96 / 164

Service Port Command Reference

hostTypeShow

The

hostTypeShow

command displays the host type setting for each FC. The possible host types are

AIX,

Gateway, ADIC SNC, HP-UX, Linux, NT

(includes

Windows 2000

)

, Netware, Generic, Solaris,

Autosense/NT,

Dell PV-132T-FC.

SNC4000 > hostTypeShow

FC 1: Type 1 - nt

icmpstatShow

The

icmpstatShow

command displays ICMP statistics for the Ethernet network. Interpreting these

statistics requires detailed knowledge of Internet networking protocols. This information may be useful to
the LAN administrator.

SNC4000 > icmpstatShow

ICMP:

0 call to icmp_error

0 error not generated because old message was icmp

0 message with bad code fields

0 message < minimum length

0 bad checksum

0 message with bad length

0 message response generated

value = 30 = 0x1e

ifShow

The

ifShow

command is used to show the Ethernet port parameters and status as shown below. The SNC

4000 will show two devices.

ibmEmac

is the Ethernet port.

is the local loopback port.

SNC4000 > ifShow

ibmEmac (unit number 0):

Flags: (0x8063) UP BROADCAST MULTICAST ARP RUNNING

Type: ETHERNET_CSMACD

Internet address: 172.16.38.48

Broadcast address: 172.16.255.255

Netmask 0xffff0000 Subnetmask 0xffff0000

Ethernet address is 00:00:60:00:00:00

Metric is 0

Maximum Transfer Unit size is 1500

0 octets received

0 octets sent

2354 packets received

2 packets sent

2354 unicast packets received

1 unicast packets sent

0 non-unicast packets received

1 non-unicast packets sent

0 input discards

0 input unknown protocols

0 input errors

102 output errors

0 collisions; 0 dropped

lo (unit number 0):

Flags: (0x8069) UP LOOPBACK MULTICAST ARP RUNNING

Type: SOFTWARE_LOOPBACK

Internet address: 127.0.0.1

Netmask 0xff000000 Subnetmask 0xff000000

Содержание SNC 4000





































































































































































Результаты поиска

Содержание SNC 4000

Отзывы:

Похожие инструкции для SNC 4000

Бренды по названию

Популярные бренды

Quantum SNC 4000, Руководство пользователя

Результаты поиска

Содержание SNC 4000

Отзывы:

Похожие инструкции для SNC 4000

Бренды по названию

Популярные бренды