Quantum SNC 4000 Скачать руководство пользователя страница 91 | Manualshive

Страница: 91 / 164

background image

SNC 4000 User’s Guide

85

gateAddrGet

The

gateAddrGet

command displays the default network gateway address if one has been set. This

address is used when connections are made to a different subnet and there are no explicit routes defined
for that subnet. Consult your network administrator for more information on the default gateway (sometimes
referred to as default router) address

.

SNC4000 > gateAddrGet

Gateway Address set to 192.168.1.1

value = 0 = 0x0

gateAddrSet

The

gateAddrSet

command changes the default network gateway address. This address is used when

connections are made to a different subnet and there are no explicit routes defined for that subnet. Consult
your network administrator for more information on the default gateway (sometimes referred to as default
router) address

.

Successful

gateAddrSet

:

SNC4000 > gateAddrSet "10.0.0.1"

value = 0 = 0x0

Failed

gateAddrSet

(1):

The following message is received when trying to set a new gateway address and that address is currently
unreachable. The following message is sent to the terminal.

SNC4000 > gateAddrSet "10.0.0.1"

gateAddrSet: Error setting current gate addr: S_errno_ENETUNREACH

value = -1 = 0xffffffff = payloadCh 0xffd418a3

The new gateway address is written to the bootup parameters to be used at the next boot. If at next boot,
the address is reachable, then it will be written to the system file. If at next boot the gateway address is not
reachable and therefore not written to the system file, the following message is displayed:

Failed

gateAddrSet

(2):

SNC4000 > gateAddrSet "172.16.76.1"

gateAddrSet: Error deleting old gateway addr: S_errno_ESRCH

Gateway Address set to 172.16.76.1 for Ethernet interface

value = 0 = 0x0

ghostIOSet [ticks]

The

ghostIOSet

command changes the number of ticks that a command remains queued for

transmissions to the target. Each tick is 1/60th of a second. The number of ticks can be set from 1 to 60. If
ticks are set to 0, command queuing is disabled.

SNC > ghostIOSet 30

Ghost I/O support is enabled.

Stale commands will be deleted after 30 ticks (500 ms).

value = 30 = 0x1e

SNC >

Parameter

Value

Valid Range

Meaning

Ticks

1/60th of a second

0-60

Number of ticks commands remain
in queue

«
...
89
90
91
92
93
...
»

Содержание SNC 4000





































































































































































Отзывы:

Нет отзывов

Похожие инструкции для SNC 4000

Mobile Ultra Memory Stick Micro

Бренд: SanDisk Страницы: 1

Бренд: Tab Страницы: 26

System Storage N3150

Бренд: IBM Страницы: 24

DURAMAX METAL GARAGE

Бренд: USP Страницы: 109

Бренд: DuraMax Страницы: 81

BAULE EVO 80 BAULE EVO 120

Бренд: garofalo Страницы: 16

DiskStation Series

Бренд: Synology Страницы: 6

Бренд: Hama Страницы: 8

USB2.0 Flash Stick

Бренд: Acer Страницы: 11

Бренд: Acer Страницы: 24

USB 2.0 Flash Stick

Бренд: Acer Страницы: 12

RAID Ready Systems

Бренд: Acer Страницы: 21

External Hard Disk Drive 500Gb

Бренд: Acer Страницы: 2

Бренд: QNAP Страницы: 55

XL-RAID-SATA-USB

Бренд: XtendLan Страницы: 20

Бренд: Spectra Logic Страницы: 21

T-Series Spectra T200

Бренд: Spectra Logic Страницы: 110

Бренд: Spectra Страницы: 184

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды