Quantum SNC 4000 Скачать руководство пользователя страница 65

Страница: 65 / 164

SNC 4000 User’s Guide

Verify that the netmask value is the same as the netmask in hex format supplied by the network
administrator.

Verify that the subnetmask is the same as the netmask. If these values are correct, go to

Step 24

If these values are not correct, proceed to

Step 22

Use the

ethAddrSet

command to set the correct IP address and netmask values.

For more information, see the

ethAddrSet

on page 78.

From the service terminal, enter the

reboot

command and wait for the SNC to finish booting.

Go back to

Step 17

Enter the command

ping

“

”

where

is four decimal

numbers separated by periods.

is the address provided by the network administrator for PING testing.

Display of successful PING test:

SNC4000 > ping "192.168.1.1", 10

PING 192.168.1.1: 56 data bytes

64 bytes from 192.168.1.1: icmp_seq=0. time=0. ms

----192.168.1.1 PING Statistics----

10 packets transmitted, 10 packets received, 0% packet loss

round-trip (ms) min/avg/max = 0/0/0

value = 0 = 0x0

Display of failed PING test:

SNC4000 > ping "192.168.1.251",10

PING 192.168.1.251: 56 data bytes

request timed out

value = -1 = 0xfffffff

If the PING test passes, go to

Step 26

If the PING test fails, inform the System Administrator that there is a network hardware problem where
the SNC is attached.

Exit this MAP.

Remove the Ethernet cable from the SNC and install the Ethernet loop back plug.

From the service terminal, enter the

diagBoot

command.

For more information, see

Diagnostic Command Reference

on page 135.

Wait for the SNC to finish booting.

Verify that the

diagmode>

prompt is displayed.

From the service port, enter the

elTest

command.

diagmode > elTest

==== Testing Ethernet ====

Init complete.

Содержание SNC 4000





































































































































































Результаты поиска

Содержание SNC 4000

Отзывы:

Похожие инструкции для SNC 4000

Бренды по названию

Популярные бренды

Quantum SNC 4000, Руководство пользователя

Результаты поиска

Содержание SNC 4000

Отзывы:

Похожие инструкции для SNC 4000

Бренды по названию

Популярные бренды