Quantum SNC 4000 Скачать руководство пользователя страница 141

Страница: 141 / 164

SNC 4000 User’s Guide

135

Diagnostic Command Reference

This section specifies the procedures used when diagnostics are required.

Boot Modes

The SNC 4000 has two modes of operation:

normal

mode and

diagmode

. Two commands are available

from the service terminal to reboot the SNC 4000 to the desired mode. The SNC 4000 remains in the
existing mode until it has been directed to reboot in the other mode.

When the SNC 4000 is booted in

diagmode

, the command prompt displayed on the service terminal is

diagmode >

. While in

diagmode

, a limited command set is available for testing the SNC 4000 interfaces.

In addition, the device drivers for the Ethernet, FC, and SCSI interfaces are disabled so loop back tests can
be performed on them.

Entering Diagnostic Mode

Use the

diagBoot

command when the special features of the SNC 4000’s diagnostic module are required.

Follow this procedure to enter diagnostic mode.

Stop all I/O.

Shut down the Scalar 24.

Remove the Ethernet cable, if installed.

Connect the terminal to the service port.

Turn on the Scalar 24and wait for it to finish booting.

If the command prompt displayed on the service terminal is

diagmode

>, proceed with the appropriate

diagnostic tests.

If the command prompt displayed on the service terminal is not

diagmode >

, enter the

diagBoot

command.

Wait for the SNC 4000 to reboot.

CAUTION

Before entering

diagmode

, you must disconnect all SCSI and FC

cables from the SNC 4000. If you do not, the data on the attached disk
or tape devices will become corrupted.

Содержание SNC 4000





































































































































































Результаты поиска

Содержание SNC 4000

Отзывы:

Похожие инструкции для SNC 4000

Бренды по названию

Популярные бренды

Quantum SNC 4000, Руководство пользователя

Результаты поиска

Содержание SNC 4000

Отзывы:

Похожие инструкции для SNC 4000

Бренды по названию

Популярные бренды