Quantum SNC 4000 Скачать руководство пользователя страница 131

Страница: 131 / 164

SNC 4000 User’s Guide

125

vpmFeatureEnabled

The

vpmFeatureEnabled

command allows you to check the status of the VPM feature. A returned value

of "1" means that VPM is already enabled. A returned value of "0" means that VPM is disabled. In the
following example, VPM is already enabled.

SNC > vpmFeatureEnabled

vpmFeatureEnabled = 0xc0199468: value = 1 = 0x1

SNC >

vps. See vpsShow

vpsAccessApply

The

vpsAccessApply

command causes the settings that have been changed and stored in memory to

take effect immediately and also saves them to the VPS or eVPS database.

SNC > vpsAccessApply

value = 0 = 0x0

SNC >

vpsAccessClear [disable code]

The

vpsAccessClear

command disables all VPS or eVPS host access to all LUNs except to LUN 0 (the

command and control interface). The disable code is stored as the "MagicNumber" in the output of the

vpsFileShow

command.

The following command example shows how to disable all access using the disable code

oxfacade03

SNC >vpsAccessClear 0xfacade03

value = 0 = 0x0

SNC >

vpsAccessSet [hostIndex],[Starting lun],[Ending lun],[Access]

The

vpsAccessSet

command sets the access for the specified range of LUNs for the specified VPS or

eVPS host connection index.

When you enter this command, the settings are stored in memory but are not applied until you enter the

vpsAccessApply

command. The following example shows how to enable the host at connection index 1

to access LUNs 2 through 32. Existing hostIndex values can be determined by looking at the "ID" column
in the output of the

vpsShow [hostIndex]

command.

SNC > vpsAccessSet 1,2,32,1

value = 0 = 0x0

SNC >

Note

When you are using Firmware 4.40 on a Fibre Channel blade, this command is
unavailable.

Access

Meaning

Disables access to the LUNs

Enables access to the LUNs

Содержание SNC 4000





































































































































































Результаты поиска

Содержание SNC 4000

Отзывы:

Похожие инструкции для SNC 4000

Бренды по названию

Популярные бренды

Quantum SNC 4000, Руководство пользователя

Результаты поиска

Содержание SNC 4000

Отзывы:

Похожие инструкции для SNC 4000

Бренды по названию

Популярные бренды